Doepfer

Looks like it may be a single rail PSU as I can only see one large 
smoothing cap so in that case it will only give +12V, however if it 
is dual rail make sure you put a 1A fuse between each power rail and 
your bussbars to limit current. Doepfer supply is 0.8 Amps, this is 
a massive 3.4 amps - if you get a short anywhere there is sufficient 
current here to burn the tracks off your bussbar and module PCB's

Other power supply to consider is the Condor (was PowerOne) HAA15-
08, it will give 1A per rail at 12 V (or 0.8A at 15V) and is used by 
MOTM, has lower noise and better regulation than standard Doepfer 
unit. Mouser part# 675-HAA15-0.8A, price $46.90

cheers,
Allan


--- In Doepfer_a100@yahoogroups.com, ben vehorn <mathlete23@c...> 
wrote:
> Thanks to those who responded.
> I'm pretty sure the way they have it worded is confusing, but I 
think 
> that it's a 12V +/- supply at 3.4A (!).
> I went ahead and ordered one.... guess I'll find out. At that 
price you 
> can't go wrong! Looks like it has a fuse and switch already wired 
up as 
> well...
> I'll let the list know once it arrives.
> --Ben
> 
> On May 13, 2005, at 1:42 PM, n keller wrote:
> 
> >
> > Ben,
> >
> > I'm no expert, but unless that is a misprint in the description 
it 
> > will not
> > work.  It is described as IN : +12-3.4A and  OUT : 
100/120/220/240 VAC 
> > .
> > This is opposite of what you are looking for.
> >
> > Call me crazy, but I'm trusting D.Doepfer to provide the best 
PSU for 
> > his
> > products.   Actually I just installed my second PSU2 into my 
system 
> > last
> > night, replacing one of the older PSU versions that always had a 
loud
> > ambient hum.   A PSU2 has more than enough power for a G6 frame, 
so 
> > I'll be
> > adding some bus-boards into another rack frame and "stealing" 
some 
> > power
> > from the G6 above.
> >
> > Good luck finding other solutions.  Again I'm no expert.
> >
> > n keller
> >
> >
> >
> >
> >
> >
> >
> >> From: ben vehorn <mathlete23@c...>
> >> Reply-To: Doepfer_a100@yahoogroups.com
> >> To: Doepfer_a100@yahoogroups.com
> >> Subject: [Doepfer_a100] Suitable PS for Doepfer
> >> Date: Fri, 13 May 2005 11:36:54 -0400
> >>
> >> Just wanted to confirm this...
> >> The following power supply should be suitable for a Doepfer 
system,
> >> correct?
> >>
> >> http://safe.spsp.net/cgi-bin/debco/OLS12C.html
> >>
> >> I'm building my own enclosure and will be using Doepfer bus 
boards to
> >> distribute the power.
> >> Thanks.
> >> --Ben
> >>
> >
> > _________________________________________________________________
> > Don't just search. Find. Check out the new MSN Search!
> > http://search.msn.click-url.com/go/onm00200636ave/direct/01/
> >
> >
> >
> >
> >
> > Yahoo! Groups Links
> >
> >
> >
> >
> >
> >