Doepfer

Thanks for the tip. It's only a $15 gamble so I very well might need a 
different one.
The Condor supply, I actually have one of these in an MOTM power supply 
that I'm trying to make redundant...if so I could use it. How would one 
go about switching it to run on 12V instead of 15V?

On May 14, 2005, at 6:26 AM, allanjhall wrote:

> Looks like it may be a single rail PSU as I can only see one large
>  smoothing cap so in that case it will only give +12V, however if it
>  is dual rail make sure you put a 1A fuse between each power rail and
>  your bussbars to limit current. Doepfer supply is 0.8 Amps, this is
>  a massive 3.4 amps - if you get a short anywhere there is sufficient
>  current here to burn the tracks off your bussbar and module PCB's
>
>  Other power supply to consider is the Condor (was PowerOne) HAA15-
>  08, it will give 1A per rail at 12 V (or 0.8A at 15V) and is used by
>  MOTM, has lower noise and better regulation than standard Doepfer
>  unit. Mouser part# 675-HAA15-0.8A, price $46.90
>
>  cheers,
>  Allan
>
>
>  --- In Doepfer_a100@yahoogroups.com, ben vehorn <mathlete23@c...>
>  wrote:
>  > Thanks to those who responded.
>  > I'm pretty sure the way they have it worded is confusing, but I
>  think
>  > that it's a 12V +/- supply at 3.4A (!).
>  > I went ahead and ordered one.... guess I'll find out. At that
>  price you
>  > can't go wrong! Looks like it has a fuse and switch already wired
>  up as
>  > well...
>  > I'll let the list know once it arrives.
>  > --Ben
>  >
>  > On May 13, 2005, at 1:42 PM, n keller wrote:
>  >
>  > >
>  > > Ben,
>  > >
>  > > I'm no expert, but unless that is a misprint in the description
>  it
>  > > will not
>  > > work.� It is described as IN : +12-3.4A and� OUT :
>  100/120/220/240 VAC
>  > > .
>  > > This is opposite of what you are looking for.
>  > >
>  > > Call me crazy, but I'm trusting D.Doepfer to provide the best
>  PSU for
>  > > his
>  > > products.�� Actually I just installed my second PSU2 into my
>  system
>  > > last
>  > > night, replacing one of the older PSU versions that always had a
>  loud
>  > > ambient hum.�� A PSU2 has more than enough power for a G6 frame,
>  so
>  > > I'll be
>  > > adding some bus-boards into another rack frame and "stealing"
>  some
>  > > power
>  > > from the G6 above.
>  > >
>  > > Good luck finding other solutions.� Again I'm no expert.
>  > >
>  > > n keller
>  > >
>  > >
>  > >
>  > >
>  > >
>  > >
>  > >
>  > >> From: ben vehorn <mathlete23@c...>
>  > >> Reply-To: Doepfer_a100@yahoogroups.com
>  > >> To: Doepfer_a100@yahoogroups.com
>  > >> Subject: [Doepfer_a100] Suitable PS for Doepfer
>  > >> Date: Fri, 13 May 2005 11:36:54 -0400
>  > >>
>  > >> Just wanted to confirm this...
>  > >> The following power supply should be suitable for a Doepfer
>  system,
>  > >> correct?
>  > >>
>  > >> http://safe.spsp.net/cgi-bin/debco/OLS12C.html
>  > >>
>  > >> I'm building my own enclosure and will be using Doepfer bus
>  boards to
>  > >> distribute the power.
>  > >> Thanks.
>  > >> --Ben
>  > >>
>  > >
>  > > _________________________________________________________________
>  > > Don't just search. Find. Check out the new MSN Search!
>  > > http://search.msn.click-url.com/go/onm00200636ave/direct/01/
>  > >
>  > >
>  > >
>  > >
>  > >
>  > > Yahoo! Groups Links
>  > >
>  > >
>  > >
>  > >
>  > >
>  > >
>
>
>
> Yahoo! Groups Links
> 	� 	To visit your group on the web, go to:
> http://groups.yahoo.com/group/Doepfer_a100/
> �
> 	� 	To unsubscribe from this group, send an email to:
> Doepfer_a100-unsubscribe@yahoogroups.com
> �
> 	� 	Your use of Yahoo! Groups is subject to the Yahoo! Terms of 
> Service.
>


[Non-text portions of this message have been removed]