Doepfer

After playing around with the module and the comments of people who tried
the prototype we are no longer sure if we will release the A-101-6. The
circuit is a bit complex (especially because of the filter mode switching
which requires altogether about 20 electronic double-throw switches) and
consequently the module will be a bit expensive. And the FETs generate a lot
of distortion in the sound as they are not linear circuits (like the
vactrols). I think we will do some sound examples and then ask interested
customers if they are willing to pay the price. Maybe we offer a lower
priced version of the module (< Euro 100) with jumpers instead of the
electronic switches. In this case the user will be able to configure the
module by means of the jumpers as lowpass, highpass or allpass.

Best wishes
Dieter Doepfer

> @Dieter,
> Are you planning two different versions of this module or are you
> just not out of which one will be released?
> Cheers,
> Danny - Syndromeda

hi

Am 23.05.2014 11:26, schrieb richyho@virginmedia.com [Doepfer_a100]:
> A little bit off-topic, but can I propose a new module that is basically
> 4hp and has 8 toggle switches and 8 LEDs to show switch state with 8
> flying leads to connect to the back of modules' jumpers. There are so
> many modules with hidden jumper functions that this would be a very useful a
I think that is a very easy DIY-Module.

Florian

Thanks Dieter, makes sense.

Greetings,

------------------------------------------------------
Danny Budts
info@syndromeda.be
www.syndromeda.be



----- Oorspronkelijk bericht -----
Van: yahoo@doepfer.de [Doepfer_a100] <Doepfer_a100@yahoogroups.com>
Aan: Doepfer a100 <Doepfer_a100@yahoogroups.com>
Verzonden: Fri, 23 May 2014 10:46:57 +0200 (CEST)
Onderwerp: AW: [Doepfer_a100] A-101-6

After playing around with the module and the comments of people who tried
the prototype we are no longer sure if we will release the A-101-6. The
circuit is a bit complex (especially because of the filter mode switching
which requires altogether about 20 electronic double-throw switches) and
consequently the module will be a bit expensive. And the FETs generate a lot
of distortion in the sound as they are not linear circuits (like the
vactrols). I think we will do some sound examples and then ask interested
customers if they are willing to pay the price. Maybe we offer a lower
priced version of the module (< Euro 100) with jumpers instead of the
electronic switches. In this case the user will be able to configure the
module by means of the jumpers as lowpass, highpass or allpass.

Best wishes
Dieter Doepfer


> @Dieter,
> Are you planning two different versions of this module or are you
> just not out of which one will be released?
> Cheers,
> Danny - Syndromeda



------------------------------------

------------------------------------

Yahoo Groups Links

... But I hope to see the A-127 BOM to be released.

Thanks again for developing all this nice stuff Dieter.

Have a nice weekend.

------------------------------------------------------
Danny Budts
info@syndromeda.be
www.syndromeda.be



----- Oorspronkelijk bericht -----
Van: yahoo@doepfer.de [Doepfer_a100] <Doepfer_a100@yahoogroups.com>
Aan: Doepfer a100 <Doepfer_a100@yahoogroups.com>
Verzonden: Fri, 23 May 2014 10:46:57 +0200 (CEST)
Onderwerp: AW: [Doepfer_a100] A-101-6

After playing around with the module and the comments of people who tried
the prototype we are no longer sure if we will release the A-101-6. The
circuit is a bit complex (especially because of the filter mode switching
which requires altogether about 20 electronic double-throw switches) and
consequently the module will be a bit expensive. And the FETs generate a lot
of distortion in the sound as they are not linear circuits (like the
vactrols). I think we will do some sound examples and then ask interested
customers if they are willing to pay the price. Maybe we offer a lower
priced version of the module (< Euro 100) with jumpers instead of the
electronic switches. In this case the user will be able to configure the
module by means of the jumpers as lowpass, highpass or allpass.

Best wishes
Dieter Doepfer


> @Dieter,
> Are you planning two different versions of this module or are you
> just not out of which one will be released?
> Cheers,
> Danny - Syndromeda



------------------------------------

------------------------------------

Yahoo Groups Links

The A-127 BOM is already in production and should be available July 2014.

Best wishes
Dieter Doepfer

> -----Ursprüngliche Nachricht-----
> Von: Doepfer_a100@yahoogroups.com [mailto:Doepfer_a100@yahoogroups.com]
> Gesendet: Freitag, 23. Mai 2014 12:10
> An: Doepfer a100
> Betreff: Re: AW: [Doepfer_a100] A-101-6
>
>
> ... But I hope to see the A-127 BOM to be released.
>
> Thanks again for developing all this nice stuff Dieter.
>
> Have a nice weekend.
>
> ------------------------------------------------------
> Danny Budts
> info@syndromeda.be
> www.syndromeda.be
>
>
>
> ----- Oorspronkelijk bericht -----
> Van: yahoo@doepfer.de [Doepfer_a100] <Doepfer_a100@yahoogroups.com>
> Aan: Doepfer a100 <Doepfer_a100@yahoogroups.com>
> Verzonden: Fri, 23 May 2014 10:46:57 +0200 (CEST)
> Onderwerp: AW: [Doepfer_a100] A-101-6
>
> After playing around with the module and the comments of people who tried
> the prototype we are no longer sure if we will release the A-101-6. The
> circuit is a bit complex (especially because of the filter mode switching
> which requires altogether about 20 electronic double-throw switches) and
> consequently the module will be a bit expensive. And the FETs
> generate a lot
> of distortion in the sound as they are not linear circuits (like the
> vactrols). I think we will do some sound examples and then ask interested
> customers if they are willing to pay the price. Maybe we offer a lower
> priced version of the module (< Euro 100) with jumpers instead of the
> electronic switches. In this case the user will be able to configure the
> module by means of the jumpers as lowpass, highpass or allpass.
>
> Best wishes
> Dieter Doepfer
>
>
> > @Dieter,
> > Are you planning two different versions of this module or are you
> > just not out of which one will be released?
> > Cheers,
> > Danny - Syndromeda
>
>
>
> ------------------------------------
>
> ------------------------------------
>
> Yahoo Groups Links
>
>
>
>
>
>
> ------------------------------------
> Posted by: syndromeda@telenet.be
> ------------------------------------
>
> Yahoo Groups Links
>
>
>

What is a BOM please?

Jonathan Shapero
From my iPad Air

> On 23 May 2014, at 11:09, "syndromeda@telenet.be [Doepfer_a100]" <Doepfer_a100@yahoogroups.com> wrote:
> 
> ... But I hope to see the A-127 BOM to be released.
> 
> Thanks again for developing all this nice stuff Dieter.
> 
> Have a nice weekend.
> 
> ------------------------------------------------------
> Danny Budts
> info@syndromeda.be
> www.syndromeda.be
> 
> 
> 
> ----- Oorspronkelijk bericht -----
> Van: yahoo@doepfer.de [Doepfer_a100] <Doepfer_a100@yahoogroups.com>
> Aan: Doepfer a100 <Doepfer_a100@yahoogroups.com>
> Verzonden: Fri, 23 May 2014 10:46:57 +0200 (CEST)
> Onderwerp: AW: [Doepfer_a100] A-101-6
> 
> After playing around with the module and the comments of people who tried
> the prototype we are no longer sure if we will release the A-101-6. The
> circuit is a bit complex (especially because of the filter mode switching
> which requires altogether about 20 electronic double-throw switches) and
> consequently the module will be a bit expensive. And the FETs generate a lot
> of distortion in the sound as they are not linear circuits (like the
> vactrols). I think we will do some sound examples and then ask interested
> customers if they are willing to pay the price. Maybe we offer a lower
> priced version of the module (< Euro 100) with jumpers instead of the
> electronic switches. In this case the user will be able to configure the
> module by means of the jumpers as lowpass, highpass or allpass.
> 
> Best wishes
> Dieter Doepfer
> 
> 
>> @Dieter,
>> Are you planning two different versions of this module or are you
>> just not out of which one will be released?
>> Cheers,
>> Danny - Syndromeda
> 
> 
> 
> ------------------------------------
> 
> ------------------------------------
> 
> Yahoo Groups Links
> 
> 
> 
> 
> 
> 
> ------------------------------------
> Posted by: syndromeda@telenet.be
> ------------------------------------
> 
> Yahoo Groups Links
> 
> 
>

stands for Bill Of Materials, i.e. a list of components used. 
 
http://www.wizardwoodcraft.co.uk/
 
Norfolk UK

>________________________________
> From: "Jonathan jss9h@aol.com [Doepfer_a100]" <Doepfer_a100@yahoogroups.com>
>To: "Doepfer_a100@yahoogroups.com" <Doepfer_a100@yahoogroups.com> 
>Sent: Saturday, 24 May 2014, 10:25
>Subject: Re: AW: [Doepfer_a100] A-101-6
>  
>   
> 
>What is a BOM please?Jonathan Shapero
>From my iPad Air
>On 24 May 2014, at 10:24, "Jonathan jss9h@aol.com [Doepfer_a100]" <Doepfer_a100@yahoogroups.com> wrote:
>This message has no content.   
>

Yeah right....;-) 

For summer 2014 the A-127 breakout module is (BOM) planned. This expansion module offers these new functions: 

    * additional notch filter for each sub-unit 
    * separate outputs for lowpass, highpass, bandpass and notch for each sub-unit 
    * separate audio input with attenuator for each sub-unit 


The breakout module allows the separate use of each of the three A-127 filters. In addition the filters can be patched parallel or serial. Especially the serial connection of three notches generates very complex phasing-like structures. For parallel filter connection the existing mixer of the main module may be used or an external mixer. For serial connection the filters are patched in the desired sequence at the breakout module. A jumper is used to define the filter type for each sub-unit for the mix unit of the main module. 

Remark : The breakout module can be used without modification only in combination with the new version of the A-127 (pcb printing "Version 4"). Only the new version has the expansion connector available, that is required to connect the breakout module. It's also possible to combine the breakout module with older versions of the A-127 (versions 1, 2 and 3) but in this case soldering is required to connect the breakout module to the main module (soldering 4 wires to each filter unit). We will publish corresponding modification instructions as soon as the breakout module will be available. 

Price: about Euro 65.00 

------------------------------------------------------ 
Danny Budts 
info@syndromeda.be 
www.syndromeda.be 


----- Oorspronkelijk bericht -----

Van: "anthony.box@talk21.com [Doepfer_a100]" <Doepfer_a100@yahoogroups.com> 
Aan: "Doepfer a100" <Doepfer_a100@yahoogroups.com> 
Verzonden: Zaterdag 24 mei 2014 11:32:10 
Onderwerp: Re: AW: [Doepfer_a100] A-101-6 




stands for Bill Of Materials, i.e. a list of components used. 
http://www.wizardwoodcraft.co.uk/ 
Norfolk UK 

From: "Jonathan jss9h@aol.com [Doepfer_a100]" <Doepfer_a100@yahoogroups.com> 
To: "Doepfer_a100@yahoogroups.com" <Doepfer_a100@yahoogroups.com> 
Sent: Saturday, 24 May 2014, 10:25 
Subject: Re: AW: [Doepfer_a100] A-101-6 
What is a BOM please?Jonathan Shapero 
F rom my iPad Air 
On 24 May 2014, at 10:24, "Jonathan jss9h@aol.com [Doepfer_a100]" < Doepfer_a100@yahoogroups.com > wrote: 

<blockquote>

This message has no content. 




</blockquote>

For those that can't read the thread because their provider has messed up the connections I think I'm correct in that the question was correctly answered. Never use sarcasm in replies it leads to irritation.! I wish I could read the threads it would make life more interesting. 
 
http://www.wizardwoodcraft.co.uk/
 
Norfolk UK
 


>________________________________
> From: "achtung_999 heinrich.himmelwasser@gmail.com [Doepfer_a100]" <Doepfer_a100@yahoogroups.com>
>To: Doepfer_a100@yahoogroups.com 
>Sent: Saturday, 24 May 2014, 15:30
>Subject: Re: AW: [Doepfer_a100] A-101-6
>  
>   
> 
>For those that did not pay attention: Yes normally it's Bill Of Materials. But in this thread it refers to this:http://www.doepfer.de/A127_BO.gif 
>On Sat, May 24, 2014 at 1:55 PM, syndromeda@telenet.be [Doepfer_a100] <Doepfer_a100@yahoogroups.com> wrote: 
> 
>>  
>>Yeah right....;-)
>>
>>
>>
>>For summer 2014 the A-127
breakout module is (BOM) planned. This expansion module offers these new functions: 
>>	* additional notch filter for each sub-unit
>>	* separate outputs for lowpass, highpass, bandpass and notchfor each sub-unit
>>	* separate audio input with attenuator for each sub-unit 
>>The breakout module allows the
separate use of each of the three A-127 filters. In addition the filters can be
patched parallel or serial. Especially the serial connection of three notches
generates very complex phasing-like structures. For parallel filter connection
the existing mixer of the main module may be used or an external mixer. For
serial connection the filters are patched in the desired sequence at the
breakout module. A jumper is used to define the filter type for each sub-unit
for the mix unit of the main module.  
>>Remark: The breakout
module can be used without modification only in combination with the new version
of the A-127 (pcb printing "Version 4"). Only the new version has the
expansion connector available, that is required to connect the breakout module.
It's also possible to combine the breakout module with older versions of the
A-127 (versions 1, 2 and 3) but in this case soldering is required to connect
the breakout module to the main module (soldering 4 wires to each filter unit).
We will publish corresponding modification instructions as soon as the breakout
module will be available. 

>>Price: about Euro 65.00 
>>
>>
>>------------------------------------------------------Danny Budtsinfo@syndromeda.be http://www.syndromeda.be/
>>
>>
>>
>>________________________________
>>
>>Van: "anthony.box@talk21.com [Doepfer_a100]" <Doepfer_a100@yahoogroups.com> Aan: "Doepfer a100" <Doepfer_a100@yahoogroups.com>Verzonden: Zaterdag 24 mei 2014 11:32:10Onderwerp: Re: AW: [Doepfer_a100] A-101-6
>>
>>   
>>stands for Bill Of Materials, i.e. a list of components used.  
>> 
>>http://www.wizardwoodcraft.co.uk/
>>
>> 
>>Norfolk UK
>> 
>>
>>
>> From: "Jonathan jss9h@aol.com [Doepfer_a100]" <Doepfer_a100@yahoogroups.com>
>>>To: "Doepfer_a100@yahoogroups.com" <Doepfer_a100@yahoogroups.com> 
>>>Sent: Saturday, 24 May 2014, 10:25
>>>Subject: Re: AW: [Doepfer_a100] A-101-6
>>>  
>>>  
>>>What is a BOM please?Jonathan Shapero
>>>From my iPad Air
>>>On 24 May 2014, at 10:24, "Jonathan jss9h@aol.com [Doepfer_a100]" <Doepfer_a100@yahoogroups.com> wrote: 
>>>This message has no content.          
>>
>>       
>

Thanks. I thought it was referring to a new kind of module!!

Jonathan Shapero
From my iPad Air

> On 24 May 2014, at 10:32, "anthony.box@talk21.com [Doepfer_a100]" <Doepfer_a100@yahoogroups.com> wrote:
> 
> 
> 
> stands for Bill Of Materials, i.e. a list of components used. 
>  
> http://www.wizardwoodcraft.co.uk/
>  
> Norfolk UK
>  
> 
> From: "Jonathan jss9h@aol.com [Doepfer_a100]" <Doepfer_a100@yahoogroups.com>
> To: "Doepfer_a100@yahoogroups.com" <Doepfer_a100@yahoogroups.com> 
> Sent: Saturday, 24 May 2014, 10:25
> Subject: Re: AW: [Doepfer_a100] A-101-6
> What is a BOM please?Jonathan Shapero
> From my iPad Air
>> On 24 May 2014, at 10:24, "Jonathan jss9h@aol.com [Doepfer_a100]" <Doepfer_a100@yahoogroups.com> wrote:
>> This message has no content.
> 
> 
>

Ah so it WAS a kind of module (break out module!). Got it now....

Jonathan Shapero
From my iPad Air

> On 24 May 2014, at 12:55, "syndromeda@telenet.be [Doepfer_a100]" <Doepfer_a100@yahoogroups.com> wrote:
> 
> 
> 
> Yeah right....;-)
> 
> For summer 2014 the A-127 breakout module is (BOM) planned. This expansion module offers these new functions:
> additional notch filter for each sub-unit
> separate outputs for lowpass, highpass, bandpass and notch for each sub-unit
> separate audio input with attenuator for each sub-unit
> The breakout module allows the separate use of each of the three A-127 filters. In addition the filters can be patched parallel or serial. Especially the serial connection of three notches generates very complex phasing-like structures. For parallel filter connection the existing mixer of the main module may be used or an external mixer. For serial connection the filters are patched in the desired sequence at the breakout module. A jumper is used to define the filter type for each sub-unit for the mix unit of the main module. 
> 
> Remark: The breakout module can be used without modification only in combination with the new version of the A-127 (pcb printing "Version 4"). Only the new version has the expansion connector available, that is required to connect the breakout module. It's also possible to combine the breakout module with older versions of the A-127 (versions 1, 2 and 3) but in this case soldering is required to connect the breakout module to the main module (soldering 4 wires to each filter unit). We will publish corresponding modification instructions as soon as the breakout module will be available.
> 
> Price: about Euro 65.00
> 
> 
> ------------------------------------------------------
> Danny Budts
> info@syndromeda.be
> www.syndromeda.be
> 
> 
> Van: "anthony.box@talk21.com [Doepfer_a100]" <Doepfer_a100@yahoogroups.com>
> Aan: "Doepfer a100" <Doepfer_a100@yahoogroups.com>
> Verzonden: Zaterdag 24 mei 2014 11:32:10
> Onderwerp: Re: AW: [Doepfer_a100] A-101-6
> 
> stands for Bill Of Materials, i.e. a list of components used. 
>  
> http://www.wizardwoodcraft.co.uk/
>  
> Norfolk UK
>  
> 
> From: "Jonathan jss9h@aol.com [Doepfer_a100]" <Doepfer_a100@yahoogroups.com>
> To: "Doepfer_a100@yahoogroups.com" <Doepfer_a100@yahoogroups.com> 
> Sent: Saturday, 24 May 2014, 10:25
> Subject: Re: AW: [Doepfer_a100] A-101-6
>  
> What is a BOM please?Jonathan Shapero
> From my iPad Air
> On 24 May 2014, at 10:24, "Jonathan jss9h@aol.com [Doepfer_a100]" <Doepfer_a100@yahoogroups.com> wrote:
> This message has no content.
> 
> 
> 
>

No offence taken. Your reply was very succinct. It is more a warning about acronyms than anything else, they can lead to confusion. 
 
http://www.wizardwoodcraft.co.uk/
 
Norfolk UK
 


>________________________________
> From: "achtung_999 heinrich.himmelwasser@gmail.com [Doepfer_a100]" <Doepfer_a100@yahoogroups.com>
>To: Doepfer_a100@yahoogroups.com 
>Sent: Saturday, 24 May 2014, 17:42
>Subject: Re: AW: [Doepfer_a100] A-101-6
>  
>   
> 
>The thread is indeed messed up. But I did not mean no offence, just could not see someone had dropped the link before.. 
>On Sat, May 24, 2014 at 4:50 PM, anthony.box@talk21.com [Doepfer_a100] <Doepfer_a100@yahoogroups.com> wrote: 
> 
>>  
>>For those that can't read the thread because their provider has messed up the connections I think I'm correct in that the question was correctly answered. Never use sarcasm in replies it leads to irritation.! I wish I could read the threads it would make life more interesting.  
>> 
>>http://www.wizardwoodcraft.co.uk/
>> 
>>Norfolk UK 
>> 
>>
>>
>> From: "achtung_999 heinrich.himmelwasser@gmail.com [Doepfer_a100]" <Doepfer_a100@yahoogroups.com>
>>>To: Doepfer_a100@yahoogroups.com 
>>>Sent: Saturday, 24 May 2014, 15:30
>>> Subject: Re: AW: [Doepfer_a100] A-101-6   
>>>  
>>>For those that did not pay attention: Yes normally it's Bill Of Materials. But in this thread it refers to this:http://www.doepfer.de/A127_BO.gif 
>>>On Sat, May 24, 2014 at 1:55 PM, syndromeda@telenet.be [Doepfer_a100] <Doepfer_a100@yahoogroups.com> wrote: 
>>> 
>>>>  
>>>>Yeah right....;-)
>>>>
>>>>
>>>>
>>>>For summer 2014 the A-127
breakout module is (BOM) planned. This expansion module offers these new functions: 
>>>>	* additional notch filter for each sub-unit
>>>>	* separate outputs for lowpass, highpass, bandpass and notchfor each sub-unit
>>>>	* separate audio input with attenuator for each sub-unit 
>>>>The breakout module allows the
separate use of each of the three A-127 filters. In addition the filters can be
patched parallel or serial. Especially the serial connection of three notches
generates very complex phasing-like structures. For parallel filter connection
the existing mixer of the main module may be used or an external mixer. For
serial connection the filters are patched in the desired sequence at the
breakout module. A jumper is used to define the filter type for each sub-unit
for the mix unit of the main module.  
>>>>Remark: The breakout
module can be used without modification only in combination with the new version
of the A-127 (pcb printing "Version 4"). Only the new version has the
expansion connector available, that is required to connect the breakout module.
It's also possible to combine the breakout module with older versions of the
A-127 (versions 1, 2 and 3) but in this case soldering is required to connect
the breakout module to the main module (soldering 4 wires to each filter unit).
We will publish corresponding modification instructions as soon as the breakout
module will be available. 

>>>>Price: about Euro 65.00 
>>>>
>>>>
>>>>------------------------------------------------------Danny Budtsinfo@syndromeda.be http://www.syndromeda.be/
>>>>
>>>>
>>>>Van: "anthony.box@talk21.com [Doepfer_a100]" <Doepfer_a100@yahoogroups.com> Aan: "Doepfer a100" <Doepfer_a100@yahoogroups.com>Verzonden: Zaterdag 24 mei 2014 11:32:10Onderwerp: Re: AW: [Doepfer_a100] A-101-6
>>>>
>>>>   
>>>>stands for Bill Of Materials, i.e. a list of components used.  
>>>> 
>>>>http://www.wizardwoodcraft.co.uk/
>>>>
>>>> 
>>>>Norfolk UK
>>>> 
>>>>
>>>>
>>>> From: "Jonathan jss9h@aol.com [Doepfer_a100]" <Doepfer_a100@yahoogroups.com>
>>>>>To: "Doepfer_a100@yahoogroups.com" <Doepfer_a100@yahoogroups.com> 
>>>>>Sent: Saturday, 24 May 2014, 10:25
>>>>>Subject: Re: AW: [Doepfer_a100] A-101-6
>>>>>  
>>>>>  
>>>>>What is a BOM please?Jonathan Shapero
>>>>>From my iPad Air
>>>>>On 24 May 2014, at 10:24, "Jonathan jss9h@aol.com [Doepfer_a100]" <Doepfer_a100@yahoogroups.com> wrote: 
>>>>>This message has no content.          
>>>>
>>>>                  
>

It's the abbreviation for breakout module, i.e. a module that expands the
features of an existing module - in this case for the A-127 triple filter.

Best wishes
Dieter Doepfer

> What is a BOM please?
>
> Jonathan Shapero