Homebrew PCBs

Mark,
I have resolved one issue... Cleaning with Acetone didn't do good enough 
of a job. After re-cleaning the carrier with mild detergent and 
scotchbrite, Drying with fresh clean cotton dish towel, I am not getting 
the paper jam indication upon the first pull, and am not getting 
residual toner on the sheet. Poor conductivity at first, I think. 
However now, when I print from the PC, the carrier pulls in to about.75 
past the trigger hole, and stops with a jam. Is this likely due to the 
high resistance of the pullup resistor (30.1k) preventing the trigger 
from working?
Thanks,
Roger


On 4/5/2015 5:31 PM, Mark mlerman@... [Homebrew_PCBs] wrote:
>
> Roger,
>
> This usually happens if the NPIS doesn't see the hole in the carrier. 
> Did you remember to drill one?
>
> Mark
>
>     -----Original Message-----
>     From: "Roger Blair Roger.Blair@... [Homebrew_PCBs]"
>     Sent: Apr 5, 2015 10:33 AM
>     To: Homebrew_PCBs@yahoogroups.com
>     Subject: Re: [Homebrew_PCBs] Re: DLP MCU version troubleshooting,
>     help needed
>
>
>
>     Hi Mark (& Marc), again...
>     I found a few overlooked corresponding emails from earlier in
>     time, and with a little more information... I have just completed
>     wiring the printer as follows, and have a fault:
>
>     E260dn DLP Hookup
>
>     *Device*
>
>     	
>
>     *Function*
>
>     	
>
>     *Conn*
>
>     	
>
>     *Color*
>
>     	
>
>     *ATtiny13 MCU*
>
>     	
>
>     *Function*
>
>     *Operator Panel*
>
>     	
>
>     *3.3V*
>
>     	
>
>     *J5-5*
>
>     	
>
>     *BL*
>
>     	
>
>     *2*
>
>     	
>
>     *Pad no.\u2019s = Pin no.\u2019s*
>
>     	
>
>     *PB3*
>
>     *Cover Open*
>
>     *Switch Wires*
>
>     	
>
>     *5V*
>
>     	
>
>     *J7-1*
>
>     	
>
>     *YE*
>
>     	
>
>     *8*
>
>     	
>
>     *VCC*
>
>     *5V*
>
>     	
>
>     *J7-2*
>
>     	
>
>     *RD*
>
>     *GND*
>
>     	
>
>     *J7-3*
>
>     	
>
>     *BK*
>
>     	
>
>     *4*
>
>     	
>
>     *GND*
>
>     *Thermistor Substitute*
>
>     	
>
>     *5V*
>
>     	
>
>     *J12-1*
>
>     	
>
>     *BK*
>
>     	
>
>     *(J12-1>2.7k>J12-2)*
>
>     *(RD-VI-RD)*
>
>     	
>
>     *Fuser Temp*
>
>     *GND*
>
>     	
>
>     *J12-2*
>
>     	
>
>     *BK*
>
>     *New Paper In Sensor*
>
>     *(was narrow sensor)*
>
>     	
>
>     *0-5V*
>
>     	
>
>     *J14-1*
>
>     	
>
>     *RD*
>
>     	
>
>     *(Splice J14-1 wire to Sensor)*
>
>     	
>
>     **
>
>     *5V*
>
>     	
>
>     *J14-2*
>
>     	
>
>     *WT*
>
>     	
>
>     *7*
>
>     	
>
>     *Pad no.\u2019s = Pin no.\u2019s*
>
>     	
>
>     *SCK*
>
>     *GND*
>
>     	
>
>     *J14-3*
>
>     	
>
>     *BK*
>
>     	
>
>     *4*
>
>     	
>
>     *GND*
>
>     **
>
>     	
>
>     *Sensor*
>
>     	
>
>     *RD*
>
>     	
>
>     *(Splice Sensor wire to J14-1)*
>
>     	
>
>     **
>
>     **
>
>     	
>
>     *Sensor*
>
>     	
>
>     *BL*
>
>     	
>
>     *5*
>
>     	
>
>     *(4.99k to PAD 8 VCC)*
>
>     	
>
>     *MOSI*
>
>     *GND*
>
>     	
>
>     *Sensor*
>
>     	
>
>     *BK*
>
>     	
>
>     *4*
>
>     	
>
>     *Pad no.\u2019s = Pin no.\u2019s*
>
>     	
>
>     *GND*
>
>     *Manual Feed*
>
>     *Paper Sensor*
>
>     	
>
>     *5V (1.1V)*
>
>     	
>
>     *J23-1*
>
>     	
>
>     *BL*
>
>     	
>
>     *Open*
>
>     	
>
>     **
>
>     *5V*
>
>     	
>
>     *J23-2*
>
>     	
>
>     *WT*
>
>     	
>
>     *6*
>
>     	
>
>     *MISO*
>
>     *GND*
>
>     	
>
>     *J23-3*
>
>     	
>
>     *BK*
>
>     	
>
>     *4*
>
>     	
>
>     *GND*
>
>     *Duplex Sensor*
>
>     	
>
>     *5V (1.1V)*
>
>     	
>
>     *J27-1*
>
>     	
>
>     *RD*
>
>     	
>
>     *Cut*
>
>     	
>
>     **
>
>     *5V*
>
>     	
>
>     *J27-2*
>
>     	
>
>     *WT*
>
>     	
>
>     *Cut*
>
>     	
>
>     **
>
>     *GND*
>
>     	
>
>     *J27-3*
>
>     	
>
>     *BK*
>
>     	
>
>     *Cut*
>
>     	
>
>     **
>
>     *Exit Sensor*
>
>     	
>
>     *5V (>0V)*
>
>     	
>
>     *J27-4*
>
>     	
>
>     *BL*
>
>     	
>
>     *Open*
>
>     	
>
>     **
>
>     *5V*
>
>     	
>
>     *J27-5*
>
>     	
>
>     *WT*
>
>     	
>
>     *3*
>
>     	
>
>     *PB4*
>
>     *GND*
>
>     	
>
>     *J27-6*
>
>     	
>
>     *BK*
>
>     	
>
>     *4*
>
>     	
>
>     *GND*
>
>     On power up with cartridge in place, the printer initializes OK.
>     When I insert a carrier and press X, the carried is pulled in
>     about half an inch or more (variable), stopping with a paper jamb
>     indicated. Pressing continue a number of times eventually pulls
>     the carrier clear of the drum, while still indicating a jamb. If I
>     cycle the power switch with the carrier in position, upon
>     initialization the carrier is automatically pulled through
>     completely. There is a light dusting of toner on both sides of the
>     carrier whenever it goes through the machine.. It appears that I
>     have something amiss...
>     Being near the bottom of the electronics food chain, I could use
>     some guidance.
>     Thanks,
>     Roger
>