Homebrew PCBs

Brian,
Very often you can use the six wire more as a 4 wire motor, simple
ignore the "center tap"
I published a free stepper motor controller design complete with PCB
layouts. This design works with any Step and Direction software..
http://hans-w.com  check the CNC page and on it there is a link to the
Modular Design.
Best of luck.
Hans W

Brian Gracia wrote:

>  Hello Everyone,
>
> I need some help starting out with CNC.  I am going to build a CNC
> router
> type machine to route pcbs.  I need some help with the circuits.
>
> I have 3-60oz in stepper motors I got from HobbyCNC.  They are marked
> STH-55D203-02 1.8 deg/step, 5.1V 1A. I believe they are unipolar from
> the
> docs and they have 6 leads coming from them. This is my first
> adventure
> with controlling stepper motors.  I have another project for CNC when
> I get
> finished with this one.  My mother (I am 34 as of Sunday) wants one of
>
> those embroidery sewing machines that cost $3000+.  She want's to do
> some
> sewing designs and monograms on clothes.  If I get my CNC
> router/driller
> working, I am going to attempt to build her one with the other group
> of 3
> unipolar stepper motors I have.
>
> I went looking for ICs to control all of the stepper motors I have.  I
> have
> a total of 6 motors, 3 being of one make and spec, and the other 3
> being of
> another make and spec.  Each group of 3 motors is the same spec, so I
> do
> not have to worry about trying to control motors of different
> characteristics.  I found the UCN5804B to be a good chip, but it will
> not
> meet the power specs of both stepper motor group I have.  They have
> different current ratings.  One group is 1A, the other 1.44A.  So, I
> will
> need some transistors that can interface with the 5804B so that no
> matter
> which motor group I am using, the circuit will power them.
>
> I found the TIP 120 to be able to put out up to 3A, which is more than
>
> enough. Page 5 of this doc:http://www.alltronics.com/download/5804.pdf
>
> shows the circuit I would like to build.  I know that I will need the
> diodes as circuit protectors.  Can anyone show me how to hook up the
> Tip's.
> I had lots of theory 12 yrs ago in college, but could not graduate do
> to
> not being able to pass calculus.  They blocked me from taking my
> Senior
> level classes.  So I wasted a lot of money!
>
> I did an extensive search on the net and came across several chips,
> but
> would still need the extra transistors to power the more current
> hungry
> motor.  Also, these chips were more expensive.  It is not that I am
> being
> cheep, I could purchase a board which many on this group seem to sell,
> it
> is just that I wish to learn more about electronics.
>
> I am looking to purchase the chips this week, so I anyone could help
> me
> out, I would appreciate it.
>
> Thanks,
> Brian G.
>
>
>                    Yahoo! Groups Sponsor
                        ADVERTISEMENT


>
> Be sure to visit the group home and check for new Bookmarks and files:
>
> http://groups.yahoo.com/group/Homebrew_PCBs
>
> To unsubscribe from this group, send an email to:
> Homebrew_PCBs-unsubscribe@yahoogroups.com
>
>
>
> Your use of Yahoo! Groups is subject to the Yahoo! Terms of Service.


[Non-text portions of this message have been removed]