Roland System 100m

hi a friend has both doepfer and 100m and as far as I know thera are no problems using the systems together.... cheers OLLIE ... am worried that the voltages

no serious problems.  driving 100m vcas with a100 oscs has you  
pushing the gain higher than normal...

On Nov 27, 2006, at 11:16 PM, synth ollie wrote:

>
> hi
>
> a friend has both doepfer and 100m and as far as I
> know thera are no problems using the systems together....
>
>
> cheers
>
> OLLIE
>
>
> >HI I was thinking of adding some doepfer modules to the 100m  
> system, but I am worried that the voltages are not >matched well.  
> The doepfer voltages are as follows : audio -5v to +5v
> >control voltages(lfos, envs etc.) - 2.5v to +2.5v and gate 0-8v. I  
> amm not sure what the votage range is on the 100m is >but I think  
> it is 0-10v.. Does anyone have any experience using doepfer and  
> 100m together as a system? thanks, >analogujeff
>
>
>
>

hello list,
i have been using the a100 with the system-100m
together for a long time now and they work fine
together, BUT, you should be carefull about the high
(+15 volts) trigger/gate outputs of the system100m
when connecting them to specific a100 inputs!
here are direct comments from Dieter Doepfer,
regarding the a100 modules list that you should NOT
connect these system100m's +15volts triger/gate outs
to:
Dieter Doepfer says:
"Yes I can verify that a +15V clock/trigger can be
applied to all
clock/gate/trigger/CV inputs of the a100, with
exception of these modules:
A-101-2 (G1 and G2 inputs)
A-112 (gate input)
A-129-5 (voiced/unvoiced inputs/output)
A-148 (all in/outputs)
A-150 (all in/outputs)
A-151 (all in/outputs)
A-152 (all in/outputs)
A-155 (external audio/CV inputs)
A-192 (all inputs)
To be on the safe side I'd recommend a simple
attenuator. I could modify an
A-180, so that the upper socket is an input and the
other three sockets are attenuated outputs that
convert +15V to about +12V.
In one A-180 module two such units could be included."



hope this helps.
best regards,
Bakis.





--- synth ollie <synth.ollie@...> wrote:

> hi
> 
> a friend has both doepfer and 100m and as far as I
> know thera are no problems using the systems
> together....
> 
> 
> cheers
> 
> OLLIE
> 
> 
> >HI I was thinking of adding some doepfer modules to
> the 100m system, but I
> am worried that the voltages are not >matched well.
> The doepfer voltages are
> as follows : audio -5v to +5v
> >control voltages(lfos, envs etc.) -2.5v to +2.5v
> and gate 0-8v. I amm not
> sure what the votage range is on the 100m is >but I
> think it is 0-10v.. Does
> anyone have any experience using doepfer and 100m
> together as a system?
> thanks, >analogujeff
> 


Bakis Sirros - Parallel Worlds
[Doepfer_a100] group owner
http://www.parallel-worlds-music.com
http://www.myspace.com/parallelworldsmusic
http://www.shimarecords.co.uk
http://www.rubber.gr
Athens-Greece


 
____________________________________________________________________________________
Cheap talk?
Check out Yahoo! Messenger's low PC-to-Phone call rates.
http://voice.yahoo.com