Analogue-sequencer

There is an install guide here:
http://www.sequentix.com/sq_lcd.htm

Sorry, should have mentioned it on the list.
I have a stock of the white on blue displays, but don't yet have the adaptor
boards to fit them with a 16 way ribbon cable.
I should have them in a few weeks, the PCB suppliers are closed over
Christmas.

Best regards,
Colin Fraser
Sequentix Music Systems Ltd
http://www.sequentix.com

 

> -----Original Message-----
> From: analogue-sequencer@yahoogroups.com 
> [mailto:analogue-sequencer@yahoogroups.com] On Behalf Of eigentone2000
> Sent: 17 December 2007 14:08
> To: analogue-sequencer@yahoogroups.com
> Subject: [analogue-sequencer] Re: PLED replacement suggestions?
> 
> Hi,
> 
> My PLED is dead, too:(
> 
> I've had to change the location of the studio. So the P3 was not
> switched on for four weeks. After this break --> PLED is black.
> 
> I've ordered a "EA Blueline LCD Display". Hope it fits.
> 
> I would really appreciate an instruction page on this.
> 
> Cheers
> Mario
> 
> 
> 
> > > I thought i had survived the curse of the PLED but it 
> looks like no to
> > > that :(
> > 
> > The PLED displays are no longer available at any of the suppliers I
> used -
> > according to one supplier, the makers of the display 
> material used have
> > stopped producing it 'for financial reasons'.
> > Maybe that means they can make more money doing colour PLEDs for MP3
> > players, or maybe they had problems with high failure rates...
> > 
> > Anyway, much as I love the appearance of the PLED displays, 
> they are not
> > that much nicer to look at than a good LCD to be worth the trouble.
> > 
> > I have been using Electronic Assembly white on blue LCD modules to
> replace
> > PLEDs that have failed in production units under warranty.
> > http://www.lcd-module.de/eng
> > Part number W162-BNLW
> > 
> > I have also looked at using Noritake LCD-compatible VFD displays,
> but these
> > are expensive (£30+), use a lot more current, and also have a
> gradual loss
> > of brightness over time.
> > 
> > Fitting an LCD module to a P3 requires 10mm M3 mounting 
> screws and 5mm
> > spacers, since the LCD modules are thicker than the PLEDs.
> > The LCD backlight also needs R19 on the P3 mainboard to be fitted.
> > The EA modules I use need a 47R resistor there. Other 
> makers modules may
> > vary.
> > 
> > On P3s with a serial number earlier than roughly #1040, the 
> function key
> > switch board is too wide to allow the LCD to be fitted, so it needs
> a bit of
> > width removed with a file.
> > I'll put together an instruction page on this soon.
> > 
> > You can wire the ribbon cable directly to the contacts on the LCD
> module,
> > and put a plug on the other end.
> > I was thinking of getting some of the little PLED to IDC 
> socket adaptor
> > boards made up, since it's a pain to remove and re-use the ones
> already on a
> > PLED module, and they didn't have connections for the 
> backlight anyway.
> > 
> > > Also is there any
> > > need for heatsinks on the power transistors etc due to 
> the increased
> > > current draw of a LCD?
> > 
> > No, it's well within the limits of the power supply.
> > Pre-production P3s used LCD modules in the first place.
> > 
> > Best regards,
> > Colin Fraser
> > Sequentix Music Systems Ltd
> > http://www.sequentix.com
> >
> 
> 
> 
> 
>  
> Yahoo! Groups Links
> 
> 
>