Cgs synth

I did it like Ken, and my module works very well. I control my Mono/Poly's
arpeggiator w/ it, and it's loads of fun. It took me a bit to learn how to
use it, though. I thought 'Trigger Out' was the burst output, but 'Pulses'
is. Silliness!

Scott

>From: sasami@...
>Reply-To: cgs_synth@yahoogroups.com
>To: cgs_synth@yahoogroups.com
>Subject: Re: [cgs_synth] Re: Burst Generator question
>Date: Sat, 8 Jun 2002 10:24:31 +1000
>
>You don't need to use any specific gnd pad. I usually run a wire from one
>of
>the gnd pads to the first jack, then a wire from that jack to the next and
>so on, and don't use the other gnd pads at all.
>
>One pot pag goes to the center, the other to the right terminal, when
>looking at the pot from the front (shaft side), with the terminals at the
>bottom.
>CLK 0 goes to the switched terminal on the "external in" jack, not the pot.
>CLK I goes to the non switched terminal on the "external in" jack. This is
>so that when you plug a jack in, the internal clock is disconnected.
>
>Cheers,
>
>Ken
>
> >Thanks, Ken. I get Trigger out, but no burst. I've probably got
> >something backwards (which POT out goes to which lug on the pot?
> >Does CLK O go to the top lug or the right lug? Which of the 3 GRDs
> >go to jacks? That kind of thing). I'll troubleshoot and let you
> >know.
> >
> >Mike
> >
> >--- In cgs_synth@y..., sasami@h... wrote:
> >> There is no bug fix on the Burst Generator. The jumpers in the
> >photo are
> >> connecting the unassigned LED to the selected output.
> >>
> >> Most likely you have a construction error - a solder bridge, bad
> >joint or
> >> whatever.
> >>
> >> Ken
> >>
> >> >Hello All -
> >> >
> >> >I just finished the BG hooked it up and no joy. Looking at the
> >> >docs, there appears to be two jumpers (bug fixes) on the back of
> >the
> >> >board. I didn't see this documented but I suspect that I need to
> >do
> >> >this.
> >> >
> >> >I get an oscilloscope on Monday so I can check the output then.
> >> >
> >> >Mike
> >>
> >_____________________________________________________________________
> >__
> >> Ken Stone sasami@h...
> >> Modular Synth PCBs for sale
> ><http://www.blaze.net.au/~sasami/synth/>
> >> Australian Miniature Horses & Ponies
> ><http://www.blaze.net.au/~sasami/>
> >
> >
> >
> >See the following URLS for the CGS Modular Synth home page:
> >http://198.164.142.50/~cgs/
> >http://shokbox.obscure.ca/~cgs/
> >
> >To unsubscribe from this group, send an email to:
> >cgs_synth-unsubscribe@yahoogroups.com
> >
> >
> >
> >Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
> >
> >
> >
>_______________________________________________________________________
>Ken Stone sasami@...
>Modular Synth PCBs for sale <http://www.blaze.net.au/~sasami/synth/>
>Australian Miniature Horses & Ponies <http://www.blaze.net.au/~sasami/>
>

_________________________________________________________________
Get your FREE download of MSN Explorer at http://explorer.msn.com/intl.asp.