I just saw the lpc2129/2114 errata earlier. So, everything's
clarified now. Updating the affected chipsets wouldn't be a problem.
Thanks again,
Leighton
--- In lpc2000@yahoogroups.com, "philips_apps" <philips_apps@y...>
wrote:
> Hello Leighton,
>
> The version of the bootloaders that do not have the improved timing
> behavior is different for the LPC210x and all other LPC2000 family
> members in the 64-pin or 144-pin package.
>
> For devices in the 64-pin package like yours, the updated version
> should be V1.63 or later. So, the bootloader you have could show
the
> problem, however, as mentioned in the Errata Sheet it affects up to
> 10% of the devices ot in other words, 90%+ of the devices will
never
> show this problem.
>
> The most critical event is an IAP call while running the device
with
> max speed at hot temperature (could be 10% failure rate). The least
> critical running it at 10-12 MHz room temp (you will probably never
> see the issue).
>
> Look at this Errata like a patch from some big company for their
> Exploration software. In all likelyhood the devices that did not
show
> the problems in a given enviroment will continue to work fine in
the
> same enviroment. A change in enviroment, speed, temperature...
could
> however trigger the misbehavior. So, if you have the opportunity to
> upgrade your bootloader version it is a good idea to do so, if not
and
> your environment does not change, no sweat.
>
> Hope this helps to clarify the issue.
>
> Best regards, Robert
>
> --- In lpc2000@yahoogroups.com, "Leighton Rowe"
<leightonsrowe@y...>
> wrote:
> > Thanks Hugh,
> >
> > I'm currently running IAP's on a PLL using lpc2129's (version
1.53
> > bootloader). So far, no problems yet.
> >
> > I notice that the errata also applies to lpc's with bootloader
> > versions below 1.52.
> >
> > It is possible that lpc's (bootloader 1.52 and above) won't
> > experience this problem?
> >
> > Leighton
> >
> >
> > --- In lpc2000@yahoogroups.com, "Hugh O'Keeffe"
<hugh.okeeffe@a...>
> > wrote:
> > > Has everyone seen the LPC2000 errata at:
> > >
> > >
http://www.semiconductors.philips.com/acrobat/erratasheets/2105.pdf
> > >
> > > Interestingly, there is a new version of the boot loader (the
on-
> > chip code
> > > that resides in LPC2000) which is upgradeable using the
Philips
> > ISP utility.
> > > Details and files are here:
> > >
> > >
> >
http://www.semiconductors.philips.com/files/products/standard/microco
> > ntrolle
> > > rs/utilities/lpc2000_bl_update.zip
> > >
> > >
> > > It seems that the IAP software (in the boot loader) has some
> > timing issues
> > > resulting in a possible 1 in 10 flash programming failure,
> > particularly when
> > > the PLL is enabled and running > 12MHz. Note: this effects all
> > methods of
> > > flash programming (i.e. via UART using Philips ISP or JTAG
using
> > Ashling
> > > PathFinder or other Debuggers) as these all call the IAP
routines.
> > >
> > > I have personally tried the upgrade and it works smoothly
using
> > the Philips
> > > ISP utility; I 'm looking at implementing a PathFinder script
for
Show quoted textHide quoted text
> > Ashling
> > > users to allow updating via JTAG
> > >
> > > HTH, Hugh @ <http://www.ashling.com/support/lpc2000/>
> > > http://www.ashling.com/support/lpc2000/
> > >
> > >
> > > [Non-text portions of this message have been removed]