I think you have all you need; you could start by trying to build one of the examples for the AT32UC3C2128.
I only used older studios with an UC3 eval board (1104?) but it worked almost OK.
I have a question too, since you mentioned the Mega1284.
I tried to "port" a 644 project to the 1284 and... its not working :-(
Granted all I did was select the 1284 instead of the 644 studio 4.18.
Would you know off-hand if there's anything else I may need?
I do use a bootloader but that part seems to be OK (chip45boot).
Best,
Cat
I only used older studios with an UC3 eval board (1104?) but it worked almost OK.
I have a question too, since you mentioned the Mega1284.
I tried to "port" a 644 project to the 1284 and... its not working :-(
Granted all I did was select the 1284 instead of the 644 studio 4.18.
Would you know off-hand if there's anything else I may need?
I do use a bootloader but that part seems to be OK (chip45boot).
Best,
Cat
> To: AVR-Chat@yahoogroups.com
> From: AVR-Chat@yahoogroups.com
> Date: Sun, 19 Oct 2014 20:56:27 -0400
> Subject: [AVR-Chat] Switching from ATMega... to AT32...
>
> I am looking into using the AT32UC3C2128 to build a CAN-to-CAN message
> bridge (store-and-forward) because it contains two integrated CAN
> controllers as well as USB & Ethernet interfaces (possible CAN-to-USB bridge
> in addition to CAN-to-CAN). I know that there are commercial units
> available but the ones I have found are priced too high for a hobby effort.
>
> So far I have only developed for the ATMega series. I need to know if I
> have the tools to support this effort.
>
> I currently use:
>
> - Atmel Studio 6.1 which lists the AT32UC3C2128 and shows a "toolchain" of
> "C:\Program Files (x86)\Atmel\Atmel Toolchain\AVR32
> GCC\Native\3.4.2.1002\avr32-gnu-toolchain\bin"
>
> - JTAG Mk II for JTAG programming and debugging. Atmel website lists the
> AT32UC3C2128 as a supported device.
>
> Am I ok to proceed?
>
> As an ATMega1284P developer is there something I should know before I
> attempt to use the AT32... ?
>
> Did I miss an 8-bit AVR that supports two CAN interfaces?
>
> Cheers,
>
> Chuck Hackett
> "Good judgment comes from experience, experience comes from bad judgment"
> 7.5" gauge Union Pacific Northern (4-8-4) 844
> http://www.whitetrout.net/Chuck
>
>
>
>
> ------------------------------------
> Posted by: "Chuck Hackett"
> ------------------------------------
>
>
> ------------------------------------
>
> Yahoo Groups Links
>
> <*> To visit your group on the web, go to:
> http://groups.yahoo.com/group/AVR-Chat/
>
> <*> Your email settings:
> Individual Email | Traditional
>;
> <*> To change settings online go to:
> http://groups.yahoo.com/group/AVR-Chat/join
> (Yahoo! ID required)
>
> <*> To change settings via email:
> AVR-Chat-digest@yahoogroups.com
> AVR-Chat-fullfeatured@yahoogroups.com
>
> <*> To unsubscribe from this group, send an email to:
> AVR-Chat-unsubscribe@yahoogroups.com
>
> <*> Your use of Yahoo Groups is subject to:
> https://info.yahoo.com/legal/us/yahoo/utos/terms/
>
> From: AVR-Chat@yahoogroups.com
> Date: Sun, 19 Oct 2014 20:56:27 -0400
> Subject: [AVR-Chat] Switching from ATMega... to AT32...
>
> I am looking into using the AT32UC3C2128 to build a CAN-to-CAN message
> bridge (store-and-forward) because it contains two integrated CAN
> controllers as well as USB & Ethernet interfaces (possible CAN-to-USB bridge
> in addition to CAN-to-CAN). I know that there are commercial units
> available but the ones I have found are priced too high for a hobby effort.
>
> So far I have only developed for the ATMega series. I need to know if I
> have the tools to support this effort.
>
> I currently use:
>
> - Atmel Studio 6.1 which lists the AT32UC3C2128 and shows a "toolchain" of
> "C:\Program Files (x86)\Atmel\Atmel Toolchain\AVR32
> GCC\Native\3.4.2.1002\avr32-gnu-toolchain\bin"
>
> - JTAG Mk II for JTAG programming and debugging. Atmel website lists the
> AT32UC3C2128 as a supported device.
>
> Am I ok to proceed?
>
> As an ATMega1284P developer is there something I should know before I
> attempt to use the AT32... ?
>
> Did I miss an 8-bit AVR that supports two CAN interfaces?
>
> Cheers,
>
> Chuck Hackett
> "Good judgment comes from experience, experience comes from bad judgment"
> 7.5" gauge Union Pacific Northern (4-8-4) 844
> http://www.whitetrout.net/Chuck
>
>
>
>
> ------------------------------------
> Posted by: "Chuck Hackett"
> ------------------------------------
>
>
> ------------------------------------
>
> Yahoo Groups Links
>
> <*> To visit your group on the web, go to:
> http://groups.yahoo.com/group/AVR-Chat/
>
> <*> Your email settings:
> Individual Email | Traditional
>;
> <*> To change settings online go to:
> http://groups.yahoo.com/group/AVR-Chat/join
> (Yahoo! ID required)
>
> <*> To change settings via email:
> AVR-Chat-digest@yahoogroups.com
> AVR-Chat-fullfeatured@yahoogroups.com
>
> <*> To unsubscribe from this group, send an email to:
> AVR-Chat-unsubscribe@yahoogroups.com
>
> <*> Your use of Yahoo Groups is subject to:
> https://info.yahoo.com/legal/us/yahoo/utos/terms/
>