Yamaha DTXpress/DTXplorer/DTXtreme

this sounds like a solution.



--- In DTXpress@yahoogroups.com, dustin howard <racetruck420@...> wrote:
>
> For this purpose a compressor is the right tool for the job. It will allow you too have much higher overall volume before clipping. Properly set-up it will remove the extreme peaks inherent in the electric kit. Google on tips to set it up. Behringer makes very usuable compressors for the money. Hope ive helped! 
> 
> --- On Thu, 3/12/09, niceguycolumbus1 <niceguycolumbus1@...> wrote:
> From: niceguycolumbus1 <niceguycolumbus1@...>
> Subject: [DTXpress] Re: help:clipping on powered speakers
> To: DTXpress@yahoogroups.com
> Date: Thursday, March 12, 2009, 12:37 PM
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> 
>     
>             Keith thanks for all your help. I feel quite inept at this. I rarely ever post to forums asking for help â€"  a combination of common sense and "reading the manual" typically gets me to the right result. 
> 
> 
> 
> However, this thing has me stumped.  I just want to plug and play. ?!?!?!?!
> 
> 
> 
> There is actually a 5 band EQ on the speaker. Dropping the base does not seem to do anything significant. Plus, I get clipping on all drum hits, it's just more obvious with the bass. So, I don't think an EQ will be the solution.
> 
> 
> 
> The bottom line here is that if I drop all input signals low enough or drop the master volume enough to reduce clipping, I am not putting out much sound. It kind of defeats the purpose of buying the speakers in the first place. My goal was a simple ability to have a live monitor alternative to headphones, plus the ability to gig a bit with it. 
> 
> 
> 
> I'm not looking to blow out the walls, so 1000w is beyond what I had in mind in terms of power and $$.
> 
> 
> 
> --- In DTXpress@yahoogroup s.com, "Keith" <keith@> wrote:
> 
> >
> 
> > Doug,
> 
> > 
> 
> > Two things you could do to reduce the bass:
> 
> > 
> 
> > 1. make sure there is no bass boost on the DTXpress - utility menu EQ Lo=0
> 
> > 
> 
> > 2. put an equaliser between the DTXpress and the amp.  I have a cheap & nasty Behringer 9 channel one - it works OK but is a horrible plastic thing (unlike the Xenyx mixer I have which is well built).
> 
> > 
> 
> > I don't think you have an equaliser on the amp, otherwise you could use that.
> 
> > 
> 
> > It is a while since I looked into clipping, but assuming things haven't changed much, the problem with clipping is that a nice low frequency sine wave gets the top chopped off.  This creates lots of high frequency harmonics which sound awful and blow up your tweeters.  With a bi-amped design that is less of a problem because the bass distortion cannot get to the tweeter.
> 
> > 
> 
> > If the clipping is not a sharp cut off, but "soft clipping" the waveform is more rounded, not as noticeable audibly and not as likely to blow anything up.
> 
> > 
> 
> > You may get some overheating of the amplifier or loudspeaker, although I would expect most amps to have a thermal trip in them.
> 
> > 
> 
> > So, if your DTXpress equaliser is already at zero, you could buy a separate one to reduce the bass a bit (or even reduce the kick volume in the kit setup) or play and keep your fingers crossed while saving up for that 1000W PA.  
> 
> > 
> 
> > Keith.
> 
> >
>