Yamaha DTXpress/DTXplorer/DTXtreme

Let's try this first: Get into midi note auto train and instruct the 
kiti to show 106 either by tapping pad 9 or manually by pressing the 
down arrow key. Make sure that 106 is the final number flashing. 
Don't hit pad 9 again, or anything else on the DTX. 

Now go right to Gain Auto Train (p. 34 in the manual) by pressing 
auto to make both yellow lights go on. Follow the rest of the 
instructions from pp. 34-36. When you're finished, hit the Visu-
lite. Is it right? If not, we'll program the C/024 (N=106) cymbal 
sound to another pad in kit 80 and switch the Visu-lite to another 
input and do the same thing.

--- In DTXpress@yahoogroups.com, jadeiebooshkie <jadiebooshkie@y...> 
wrote:
> Aha!  Ed...ther IS CROSS TALK!  It is coming from tom2
> that sits under my ride, but the note for tom 2 is
> 47(B1).  For 1 second I was able to get a cymbal sound
> on the ride...I don't know how to program the KITI...I
> would stirke the Visulite-press AUTO TRAIN then hit
> pad 9 for the cymbal...it still flashed 1-1-3 si I
> used the arrows to make it flash to note 106-what it
> SHOULD read, then I pressed SAVE and waited a minute
> then I tapped the Visulite, and got the cymbal sound,
> but then I lost the cymbal sound, when I tap the pad
> hard, that's when I get a high pitched bell sound on
> one section of the pad, and if I tap it near the
> piezo, that's when I get a tom sound.  This should be
> easier than this...something isn't right...I have NO
> note numbers of 1-1-3 in my kit for any pads.  I am
> wondering if the KITI needs to be re-programmed? Just
> a thought.  
> Jade
> --- "liberatusvirus <liberatusvirus@y...>"
> <liberatusvirus@y...> wrote:
> > Are you by any chance hitting the pad on input 10
> > instead of input 
> > 9? Or is there conceivably enough crosstalk when you
> > hit 9 that 
> > another pad's note number is going through? Check to
> > see whether one 
> > of kit 80's other inputs (a tom?) carries note
> > number 113. If so, 
> > see if you can figure out how it's taking over.
> > 
> > --- In DTXpress@yahoogroups.com, jadeiebooshkie
> > <jadiebooshkie@y...> 
> > wrote:
> > > 
> > > 
> > > Here's what I did...I re read your last post...I
> > went
> > > into the UTILITY Menu and FOUND one mistake I
> > made:
> > > I now have these:
> > > UT MAP N=106A#6 (this was listed as no assign)
> > > =C/024 Ride Em  (This is for pad 9)
> > > 
> > > Under VOICE MENU
> > > KIT*In=pad9
> > > Copy To In=pad9
> > > USER KIT 80 pad 9 showed the note 106A#6 with
> > C/024
> > > Ride Em
> > > I unplugged the KITI and replugged it in Visulite
> > is
> > > in input 1 on KITI, input 1 is lit the red lights
> > on
> > > the KITI registered 0-0-1.  I tapped the Visulite
> > then
> > > pressed Auto Train on the KITI the 0-0-1 still
> > > flashed, then I hit pad 9 (that's plugged into DTX
> > > channel 9/10)...all the red lights lit up to MIDI
> > NOTE
> > > then the 1-1-3 started to flash, as it did before,
> > not
> > > 106 as it should be.  When I listen to the
> > visulite in
> > > my headphones, the sound it is picking up is a tom
> > > sound...SOMETHING is not right, and I don't know
> > if
> > > I'M doing something wrong, or if there's something
> > not
> > > set with the DTX or if it's the KITI...I hit pad 9
> > and
> > > get a cymbal from kit 80, I hit the visulite, and
> > I
> > > get a tom...can you think of anything that may be
> > the
> > > problem...could the 9/10 split input on the DTX be
> > > confusing the KITI?
> > > Thanks for your help and patience with me,
> > > Jade
> > > --- "liberatusvirus <liberatusvirus@y...>"
> > > <liberatusvirus@y...> wrote:
> > > > We're getting there. 
> > > > 
> > > > > PS...one more thing....I unplugged the ride
> > from
> > > > the
> > > > > KITI and plugged it into input 2 on KITI...I
> > am
> > > > still
> > > > > getting the tom sound...that WASN'T a high
> > pitched
> > > > > noise I heard...it was a tom voice.  So my pad
> > 9
> > > > that
> > > > > was my 3rd tom is now on my RIDE...I can't
> > change
> > > > the
> > > > > note number on the KITI...it keeps flashing
> > 1-1-3
> > > > > instead of 0-2-4 or 0-2-6....It's gotta be
> > > > something I
> > > > > am doing wrong with the DTX.
> > > > 
> > > > It doesn't matter which input on the kiti you're
> > > > using; the midi 
> > > > note number gets transferred to the kiti's
> > active
> > > > input, which you 
> > > > select either by hitting the pad connected to it
> > or
> > > > scrolling 
> > > > through the inputs (the green lights) manually
> > on
> > > > the kiti keyboard.
> > > >  
> > > > > UT MAP N=65F...C/026 Rider3
> > > > 
> > > > This is the only setting that matters for
> > getting
> > > > the midi note 
> > > > information from the DTX to the kiti. Midi note
> > > > number 65 also has 
> > > > to show up as the note number for pad 9 when you
> > > > check in the voice 
> > > > menu of kit 80. If so, save kit 80 with the
> > button
> > > > on the front of 
> > > > the module. If not, don't do anything else until
> > you
> > > > make these 
> > > > numbers match; if 65 turns out not to work, try
> > > > other numbers. Save 
> > > > kit 80 when you've arrived at a viable note
> > number
> > > > for C/026 on 
> > > > input 9, just to make sure that you don't change
> > > > anything by 
> > > > mistake. (Acoustic kit 1 is irrelevant to what
> > we're
> > > > doing. If you 
> > > > set up the note number for the ride on the kiti
> > > > correctly, you'll 
> > > > get the same ride sound for the visulite, no
> > matter
> > > > what kit on the 
> > > > DTX you happen to be using).
> > > >  
> > > > To keep it simple on the kiti, disconnect
> > everything
> > > > but the 
> > > > visulite bow. Hit the visulite to select its
> > input.
> > > > Now, 
> > > > press "AUTO" to make "midi note number" the
> > active
> > > > parameter; three 
> > > > red lights corresponding to a midi note number
> > > > (probably not yours) 
> > > > should be blinking consecutively, with a pause
> > > > between each complete 
> > > > cycle. Making sure that your foot is not on
> > either
> > > > the hi hat 
> > > > controller or the kick pedal, hit pad 9, C/026,
> > in
> > > > kit 80; don't 
> > > > accidentally hit any other pad afterward. After
> > > > recognizing the 
> > > > default channel 10, the kiti red lights should
> > start
> > > > to register 0-6-
> > > > 5, or whatever your final midi note number
> > turned
> > > > out to be in the 
> > > > DTX utility menu. If the correct number flashes,
> > you
> > > > can continue 
> > > > to "Gain Auto Train" on p. 34 to adjust the
> > > > triggers. If it doesn't, 
> > > > it's back to the DTX to figure out why. 
> > > > 
> > > > 
> > > > > 
> > > > > 
> > > > > --- jadeiebooshkie <jadiebooshkie@y...> wrote:
> > > > > > 
> > > > > > 
> > > > > > Here's what I have done... I changed my user
> > kit
> > > > > > number to 80-went into voice and copied the
> > ride
> > > > > > setting to pad 9...when I hit pad 9 it
> > sounds
> > > > like a
> > > > > > ride...the Visulite is plugged into KITI
> > input
> > > > 1.  I
> > > > > > went into UTILITY Voice here are my
> > settings:
> > > > > > UT MAP N=10A#-2
> > > > > > C=/024
> > > > > > I then went to the KITI and pressed AUTO
> > > > TRAIN-hit
> > > > > > pad
> > > > > > #9 and the numbers blinking were 1-1-3!!!  I
> > > > tapped
> > > > > > the Visulite (plugged into KITI) and the
> > > > friggin'
> > > > > > thing sounds like a high pitched bell/ then
> > it
> > > > > > sounded
> > > > > > like pad#9's original setting in my user
> > > > kit...which
> > > > > > was a 3rd tom!!  WHAT the hell am I doing
> > > > > > wrong...also...should I copy this UT MAP
> > Copy
> > > > from=1
> > > > > > Acoustic kit??
> > > > > > How do I move the cymbal from user kit 80 to
> > the
> > > > > > KITI...and WHY is it flashing a 1-1-3
> > instead of
> > 
> === message truncated ===
> 
> 
> __________________________________________________
> Do you Yahoo!?
> Yahoo! Shopping - Send Flowers for Valentine's Day
> http://shopping.yahoo.com