Digital BW, The Print

If a lot of air has gotten above the inlet, priming the cart is the best way
to remove it.  Of course, this takes a syringe and modified MIS bottom fill
adapter, and it wastes ink.  My version of a modified bottom fill adapter is
shows at http://home1.gte.net/res09aij/Mod_Bot_Fill.jpg, MIS has another
approach.  See the bottom of my Readme on the C86, at
http://home1.gte.net/res09aij/C86-EZ-UT-Readme.htm , for my suggestions on
how to most cheaply use the C86 EZ system.

Paul
www.PaulRoark.com 


> -----Original Message-----
> From: DigitalBlackandWhiteThePrint@yahoogroups.com
> [mailto:DigitalBlackandWhiteThePrint@yahoogroups.com] On Behalf Of lmpipes
> Sent: Friday, November 25, 2005 3:45 PM
> To: DigitalBlackandWhiteThePrint@yahoogroups.com
> Subject: [Digital BW] Problems with MIS EZN in C86
> 
> This is my first post to the group, so thank you in advance for your help.
> 
> Recently I purchased the MIS EZN ink for use in a C86 printer. I popped
> the cartridges in
> and tried printing, not realizing that there was a foil sticker that
> needed to be removed
> over the ventilation hole (no instructions were sent with the
> cartridges!). After I got those
> suckers off (which was quite an effort), my first print yielded terrible
> banding.
> 
> The MIS tech support has suggested all these remedies, which I've tried to
> no avail:
> 
> 1) Making sure ventilation holes are uncovered (yep! Poked a paper clip
> wire into them to
> make sure).
> 2) Leaving cartridges sit outside the printer for a day to eliminate any
> air bubbles.
> 2) Running a cleaning cycle (Did two for good measure, plus ran several
> nozzle checks.
> Perhaps a small improvement, but still there is banding).
> 
> Before using the MIS cartridges, I used the Epson color cartridges and had
> no problem with
> printing.
> 
> I have noticed than the cyan prints fine, the black with very small
> banding, the yellow and
> magenta with the worst banding.
> 
> Any suggestion? Thank you,
> 
> LPipes
> 
> 
> 
> 
> 
> 
> 
> 
> 
> Please visit the Group Homepage to check the Files, and other resources as
> they are often being updated.
> 
> http://groups.yahoo.com/group/DigitalBlackandWhiteThePrint
> 
> If you wish to receive no emails or just a daily digest, or you wish to
> unsubscribe, please edit your Membership preferences by visiting this same
> page.
> 
> Please follow these basic guidelines:
> - As threads develop, trim off excess portions of earlier messages to keep
> them short.
> - Good manners are required at all time. No personal attacks or flames.
> Hostile, aggressive or argumentative users may be removed from the
> membership without notice.
> - Keep your posts and threads related to the group topic of digital B&W
> printing. Users who persistently make off-topic posts may be removed from
> the membership.
> - By posting on this forum you agree to abide by the group rules and
> guidelines, and to abide by the actions and decisions of the group Owner
> and Moderators. See "Group Topic, Rules and Guidelines" in the Files
> section:
> http://groups.yahoo.com/group/DigitalBlackandWhiteThePrint/files/
> 
> BY PARTICIPATING IN AND/OR POSTING MESSAGES TO THE DIGITAL BW, THE PRINT
> YAHOO! GROUP YOU EXPRESSLY UNDERSTAND AND AGREE THAT THE "OWNER" AND
> "MODERATORS" OF DIGITAL BW, THE PRINT YAHOO GROUP SHALL NOT BE LIABLE TO
> YOU FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, CONSEQUENTIAL OR
> EXEMPLARY DAMAGES, INCLUDING BUT NOT LIMITED TO, DAMAGES FOR LOSS OF
> PROFITS, GOODWILL, USE, DATA OR OTHER INTANGIBLE LOSSES (EVEN IF THE
> "OWNER" AND "MODERATORS" OF DIGITAL BW, THE PRINT YAHOO GROUP HAVE BEEN
> ADVISED OF THE POSSIBILITY OF SUCH DAMAGES), RESULTING FROM: (i) THE USE
> OR THE INABILITY TO USE THE DIGITAL BW, THE PRINT YAHOO GROUP; (ii)
> UNAUTHORIZED ACCESS TO OR ALTERATION OF YOUR TRANSMISSIONS OR DATA; (iii)
> STATEMENTS OR CONDUCT OF ANY THIRD PARTY ON THE DIGITAL BW, THE PRINT
> YAHOO GROUP; OR (iv) ANY OTHER MATTER RELATING TO THE DIGITAL BW, THE
> PRINT YAHOO GROUP.
> 
> Yahoo! Groups Links
> 
> 
> 
> 
>