Doepfer

thanks for clearing out on the price differences, dieter.

i have edited the poll text to reflect that,
but i didn't know that this would delete the
already given votes.

i'm sorry about that, but there were only three votes
given anyway, so i hope that it was not a too bad mistake.

those three voters, please accept my apologies and vote again.

many thanks

best wishes

ingo


--- In Doepfer_a100@yahoogroups.com, <hardware@...> wrote:
>
> Thank's for the poll.
> 
> I hove some comments concerning the prices of the different options:
> 
> The rotary switches used in the A-110 and A-111 are very expensive 
parts.
> Consequently:
> 
> 1. Three toggle switches for octave selection (1, 2, 4 octaves) 
would be
> about the same as the rotary switch
> 2. Even the multiturn potentiometer will be in the same price range 
as the
> rotary switch
> 
> Option 1 would be the cheapest solution as neither a rotary switch 
nor a
> multiturn potentiometer is used.
> All other option are approximately in the same price range.
> By far the most expensive solution is those with rotary switch and 
multiturn
> potentiometer.
> 
> I'm very interested in the winner. I'd recommend version ....  - 
no, I don't
> want to influence your votes.
> 
> Best wishes
> Dieter Doepfer
> 
> 
> > -----Ursprüngliche Nachricht-----
> > Von: Doepfer_a100@yahoogroups.com 
[mailto:Doepfer_a100@yahoogroups.com]
> > Gesendet: Mittwoch, 13. September 2006 16:26
> > An: Doepfer_a100@yahoogroups.com
> > Betreff: [Doepfer_a100] New poll for Doepfer_a100
> >
> >
> >
> > Enter your vote today!  A new poll has been created for the
> > Doepfer_a100 group:
> >
> > which tuning controls would you prefer for the forthcoming
> > a111/2 dynamic vco?
> >
> >   o coarse freq pot with extended range + fine freq pot (like on
> > the preliminary frontpanel)
> >   o coarse freq pot with standard range + fine freq pot + rotary
> > octave switch (like a111)
> >   o coarse freq pot with extended range + fine freq pot + rotary
> > octave switch
> >   o coarse freq pot with three-position switch to select the knob
> > range + fine freq pot + rotary octave switch
> >   o coarse freq pot with jumper on the pcb to select the knob
> > range + fine freq pot + rotary octave switch
> >   o coarse freq pot with extended range + fine freq pot + a set
> > of buttons to select the octaves (probably more expensive)
> >   o coarse freq pot with extended range + fine freq multiturn pot
> > + rotary octave switch (probably more expensive)
> >   o only one bigger multiturn pot with extended range (probably
> > more expensive)
> >   o i'm fine with any of the cheaper solutions (1 - 5)
> >   o i'm fine with any of these solutions
> >
> >
> > To vote, please visit the following web page:
> > http://groups.yahoo.com/group/Doepfer_a100/surveys?id=12420582
> >
> > Note: Please do not reply to this message. Poll votes are
> > not collected via email. To vote, you must go to the Yahoo! Groups
> > web site listed above.
> >
> > Thanks!
> >
> >
> >
> >
> >
> >
> >
> >
> >
> >
> >
> > Yahoo! Groups Links
> >
> >
> >
> >
> >
> >
> >
> >
> >
> >
>