Doepfer

Well, the thing is that my Doepfer 5V adaptor broke, so I haven't tested the MT9 yet, but I have ordered one that will arrive today.

MT9:
"Introduction
The MT9 is a MIDI to triggering module. It allows triggering of a range of analogue devices; drum voice modules, envelope modules, analogue sequencers, analogue drum machines, and anything else with a gate, trigger or clock input.
It has 9 separate 5v trigger outputs, so 9 devices can be independently triggered via separate MIDI keys. There is also an ACCent output.

ACCENT
The ACC is an on (5v) / off (0v) output. When velocity of over 80 is received for any of the 9 triggers, then the Accent will go high (5v). Lower than 80 the output will go low (0v). Use this output to control other analogue modules.
Note: it is not directly compatible with the drum module ACC inputs. The naming of this socket is perhaps misleading if you use our drum modules. The drum modules require a different type of accent signal; 12v on, about 5v off. We may (or may not) make an 'Accent' add-on module.

Outputs:
9 independent trigger outs + Accent on/off
MIDI Thru
Power supply:
+5V, GND Doepfer A100 type power sockets"



I believe it's a short trigger signals and this would be perfect for switching the A-150, if the CV input was a trigger input...

Thanks, I really appreciate your help.
Best wishes
Simon



--- In Doepfer_a100@yahoogroups.com, <yahoo@...> wrote:
>
> Does your MT9 output 9 gates (i.e. the output remains high until the
> corresponding note off message is transmitted) or only short trigger signals
> ? If gate signals are available the A-150 should do the job. Otherwise A-151
> can be used (in this case the state changes with each trigger pulse).
> 
> Best wishes
> Dieter Doepfer
> 
> 
> > -----Ursprüngliche Nachricht-----
> > Von: Doepfer_a100@yahoogroups.com
> > [mailto:Doepfer_a100@yahoogroups.com]Im Auftrag von Simon
> > Gesendet: Dienstag, 20. April 2010 10:48
> > An: Doepfer_a100@yahoogroups.com
> > Betreff: [Doepfer_a100] Re: Can I trigger the CV on the Doepfer A-150 ?
> >
> >
> > I use the A-150 as a gate; audio/CV signal IN1, nothing in IN2,
> > audio out I/O.
> >
> > I know that the A-151 is capable of this - I have one myself -
> > but since the A-150 is made of two identical modules, this would
> > save me a lot of rack space.
> > The thing is that I would need six A-150 instead of twelve A-150!
> >
> > The MT9 midi-trig from Analogue Solutions can switch between nine
> > trigger signals and what is very important, I can make Max/Msp
> > switch between the nine triggers in any order I like.
> > So with two MT9 and six A-150 it would be possible to have plenty
> > of "gates" incorporated in my modular system and only use 44 HP
> > of rack space.
> > Isn't this the best solution, if the A-150 can be triggered, for
> > my system?
> >
> > Best wishes
> > Simon
> >
> >
> > --- In Doepfer_a100@yahoogroups.com, <yahoo@> wrote:
> > >
> > > > I have tested the Doepfer A- 152, but it doesn't seem to suit
> > my needs.
> > > > Is it possible to change the CV inputs of the A-150 to a
> > trigger input?
> > > > Or maybe it's too expensive?
> > > > Thanks
> > > > Simon
> > >
> > > From what you asked for several A-152 should be right solution.
> > >
> > > Anyway: What should the A-150 trigger input do:
> > >
> > > a) toggle between the two inputs ?
> > > b) switch to input #2 as long the trigger signal is high ?
> > >
> > > Version a) is already available with the A-150. If you want to toggle
> > > between 2 inputs the A-151 could be used (limited to 2 steps by
> > means of the
> > > switch).
> > >
> > > Best wishes
> > > Dieter Doepfer
> > >
> >
> >
> >
> >
> > ------------------------------------
> >
> > Yahoo! Groups Links
> >
> >
> >
>