Doepfer

"and for the Analogue systems modules made one out of a
strip of Vero board."
This is what I wanted to know. :)

For me, the 650mA (or something) coming out of the Asol PS will be 
more than sufficient,I think. I'm planning a 9U system (19"). Which 
should both fit the need as an external signal processor as well as 
a "simple" Dual VCO mono synth. But it will take ages for me to fill 
the full 9U, since I don't  have a big budget.

But, what's  a Vero board, where can I find one and how do I make a 
strip from it?

Thanks for all the info!!

Greetings, Zameer

--- In Doepfer_a100@y..., David Salter <david.salter@r...> wrote:
> Hi there Zameer,
>  
> I know your question wasn't for me but I'll provide an answer 
anyway as I have an equally large system of different euro modules.
>  
> What is needed is a good quality LINEAR (not switch mode) power 
supply providing +/- 12V with sufficient ampage to support your total 
module set (and planned expansion).
>  
> These can be purchased from many suppliers, mine was from an UK 
based company 
> 
> http://www.amplicon.co.uk <http://www.amplicon.co.uk>  
> 
> Mine is (well there are two actually) 1.7A open frame Bentron S 
series supplies, and I am very happy with them.
> 
> All that is necessary is to connect the -12/+12 and ground to a bus 
board ( I use the Doepfer ones and for the Analogue systems modules 
made one out of a strip of Vero board.
> 
>  
> 
> Hope that helps
> 
>  
> 
> Regards
> 
>  
>  
> 
> David Salter 
> Reuters Consulting 
> Tel: +44 20 7542 2402 
> Mob: +44 7990562402 
> Fax: +44 20 7542 2699 
> 
> 	-----Original Message-----
> 	From: flamey101 [mailto:flame101@p...] 
> 	Sent: 11 September 2002 23:43
> 	To: Doepfer_a100@y...
> 	Subject: [Doepfer_a100] Re: Slighty OT (again): Analogue 
Systems ADSR mods
> 	
> 	
> 	I have one queation to you, Peter, since you have a bunch of 
> 	different euro-modules in your systems..
> 	My current setup (a reeeaaal small one compared to yuors) 
cosists of:
> 	An AS Filter, Osc, Doepfer amp, controls, etc.. isn't 
important to my 
> 	question actually.
> 	I have a Analogue Solutions Power supply board, on which I 
can plug 2 
> 	ASys modules into (the Osc and the filter). I do want to 
expand my 
> 	system with a frequency-to-voltage Asys thingie and add an 
extra 
> 	filter and Osc, maybe an extra Osc ass a waveshaper LFO. Or 
could I 
> 	get the same results with a slew limiter(?). So, what I was 
> 	wondering, how did you supply the volts to your AS modules?
> 	Did you built connectors/or cables yourself (hopefully)?
> 	
> 	Greets, Zameer
> 	
> 	--- In Doepfer_a100@y..., "(i think you can figure that out)" 
> 	<petergrenader@h...> wrote:
> 	> Sorry for this interesting, but slightly off-topic posting:
> 	> 
> 	> for those of you interested in the mods I did on my 
Analogue 
> 	> Systems ADSR, go to:
> 	> 
> 	> http://www.allegrobikes.com/franken.html
> 	> 
> 	> and click on the the link 'modifications' in the first 
paragraph of 
> 	> descriptive text on the expansion panel.
> 	
> 	
> 	
> Yahoo! Groups Sponsor	
> ADVERTISEMENT
>  
<http://rd.yahoo.com/M=226671.2265556.3698777.2225242/D=egroupweb/S=17
05032144:HM/A=1201365/R=0/*http://shop.store.yahoo.com/cgi-bin/clink?
sharperimage-
best+KFTN2Y:dmad/M=226671.2265556.3698777.2225242/D=egroupweb/S=170503
2144:HM/A=1201365/R=1/1031784173+si637.html> 	
>  <http://us.adserver.yahoo.com/l?
M=226671.2265556.3698777.2225242/D=egroupmail/S=:HM/A=1201365/rand=448
695315> 	
> 
> 	To unsubscribe from this group, send an email to:
> 	doepfer_a100-unsubscribe@y...
> 	
> 	
> 	
> 	Your use of Yahoo! Groups is subject to the Yahoo! Terms of 
Service <http://docs.yahoo.com/info/terms/> . 
> 	
> 
> 
> 
> ------------------------------------------------------------- ---
>         Visit our Internet site at http://www.reuters.com
> 
> Any views expressed in this message are those of  the  individual
> sender,  except  where  the sender specifically states them to be
> the views of Reuters Ltd.
> 
> 
> [Non-text portions of this message have been removed]