Doepfer

Dear Bakis,
Thanks very much for this info !

I just invested an hour to create a temporary solution myself;

This SY02 module sounds great ! It has the typical distorted, dirty 
MS sound (just compared it side by side to my MS-10). hats off to A. 
Sol. !
I have been able to get close to this sound by using two A-121's and 
a A-116 after the filters, but the flexibility of the SY02 (it has an 
integrated VCA) makes it a very nice module.
Any way, I will buy Doepfer's 101 anyway when it gets available, but 
I am not sure when it's due.

Regards
Joost

--- In Doepfer_a100@yahoogroups.com, Bakis Sirros 
<synth_freak_2000@y...> wrote:
> hi joost,
> what?the sy02 should have a doepfer connector in it's
> pcb.maybe you have got a sy02 with an Analogue Systems
> socket.the doepfer connector is the default one for
> A.SOL. modules.ask tom carpenter for this!if your used
> sy02 has an ANALOGUE SYSTEMS socket, you will need an
> "analogue systems to doepfer" converter cable.
> bakis.
> 
> 
> --- levka0 <levka@w...> wrote:
> > Thanks Bakis for this info
> > Sadly, the doepfer cable sockets do not fit into the
> > AS module 
> > sockets (too wide), so I will need to order an AS
> > cable first
> > 
> > I will post again once I get it working
> > 
> > regards
> > Joost
> > 
> > --- In Doepfer_a100@yahoogroups.com, Bakis Sirros 
> > <synth_freak_2000@y...> wrote:
> > > hi joost,
> > > yes,the doepfer and a.sol. ribbon cables are the
> > same,
> > > AFAIK.the red stripe goes to the word"stripe" or
> > to
> > > -12volts.so,in most of the A.SOL. modules the
> > ribbon
> > > connector goes with the red stripe up.if you look
> > at
> > > the doepfer buss board and the SY02 pcb ,you will
> > know
> > > how to connect the ribbon cable.the ribbon cable
> > goes
> > > with the red stripe at the bottom in the doepfer
> > > board!(stripe to -12volts.)
> > > bakis.
> > > 
> > > 
> > > 
> > > --- levka0 <levka@w...> wrote:
> > > > Hi There
> > > > I just got a used AS SY02 filter (could not wait
> > for
> > > > Doepfer's own MS-
> > > > 20 reincarnation ;)), and I am wondering how to
> > > > connect it.
> > > > The AS site gives some advise; it appears that
> > on
> > > > the AS modules the 
> > > > -12 V pin is located at the top side of the
> > > > connector (in contrast 
> > > > with doepfer's own modules); so it seems to me
> > that
> > > > AS should 
> > > > connect "upside-down" compared to Doepfer.
> > > > 
> > > > Anybody here with a clue ?
> > > > 
> > > > regards
> > > > Joost
> > > > 
> > > > 
> > > 
> > > 
> > > =====
> > > Bakis Sirros
> > > Parallel Worlds / Polariton
> > > Athens-Greece
> > > [Doepfer_a100] group owner
> > > http://www.rubber.gr
> > > http://www.ward12.com
> > > 
> > > __________________________________
> > > Do you Yahoo!?
> > > Yahoo! SiteBuilder - Free, easy-to-use web site
> > design software
> > > http://sitebuilder.yahoo.com
> > 
> > 
> 
> 
> =====
> Bakis Sirros
> Parallel Worlds / Polariton
> Athens-Greece
> [Doepfer_a100] group owner
> http://www.rubber.gr
> http://www.ward12.com
> 
> __________________________________
> Do you Yahoo!?
> Yahoo! SiteBuilder - Free, easy-to-use web site design software
> http://sitebuilder.yahoo.com