Doepfer

Sidney, I was just pointing out that your way of addressing Dieter Doepfer
was not polite. Being polite is obviously not a requirement; you can address
him any way you like. 

 

It's just that in an online forum specifically dedicated to Doepfer products
one would expect participants to at least know whom they are talking to.

 

As for respect, in this forum I'll respect plenty of people. Attitude
without substance will not impress me though. 

 

  _____  

Von: Doepfer_a100@yahoogroups.com [mailto:Doepfer_a100@yahoogroups.com] Im
Auftrag von Sidney
Gesendet: Donnerstag, 17. Februar 2011 15:36
An: Doepfer_a100@yahoogroups.com
Betreff: [Doepfer_a100] Re: Can't trigger A-140 from A-190-2

 

  

York, you have been extremely rude in the way you are trying to show your
'Yes Sir, No Sir' etiquette rules. 

As it is stated, "This group is about sharing tips,opinions and general
knowledge about the A100 modular synthesizer", and people come seeking this
from all over the world. 

So try to be kind next time you show your arrogance from wathever country or
culture you are, because you know that this kind of attitude leads to
nowhere. 

Neither you are officially speaking in the name of anyone in this group.
Show some respect. 

Sidney. 

--- In Doepfer_a100@yahoogroups.com <mailto:Doepfer_a100%40yahoogroups.com>
, "York Luethje" <ybl@...> wrote:
>
> Doepfer is his last name. Polite people will address him as Mr / Herr
> Doepfer or with his first name Dieter if you're Anglo-Saxon /
Scandinavian.
> Just calling him 'Doepfer' is seriously rude. 
> 
> 
> 
> _____ 
> 
> Von: Doepfer_a100@yahoogroups.com <mailto:Doepfer_a100%40yahoogroups.com>
[mailto:Doepfer_a100@yahoogroups.com <mailto:Doepfer_a100%40yahoogroups.com>
] Im
> Auftrag von Sidney
> Gesendet: Donnerstag, 17. Februar 2011 01:10
> An: Doepfer_a100@yahoogroups.com <mailto:Doepfer_a100%40yahoogroups.com> 
> Betreff: [Doepfer_a100] Re: Can't trigger A-140 from A-190-2
> 
> 
> 
> 
> 
> Doepfer, I successfully replaced the A-190-2 defective Q1 with a new
BC547B
> transistor. Now the gate is working. But I think that the CV V/V is not
> working. I didn't test it before. Is there a way to fix it?
> 
> Thank you,
> 
> Sidney
> 
> --- In Doepfer_a100@yahoogroups.com
<mailto:Doepfer_a100%40yahoogroups.com>
<mailto:Doepfer_a100%40yahoogroups.com>
> , <yahoo@> wrote:
> >
> > > I think I had plugged the A190-2 the wrong way the first time I
> > > plugged it into the power bus board, and might damaged the unit.
> > > It seemed to be working fine, as it was receiving midi messages
> > > and activating the A110 both from the CV1 and pitch bend from
> > > CV2. But the gate output problem and out of tune scale indicated
> > > there is something wrong really. Maybe I will be necessary to buy
> > > a new one.
> > >
> > > Thank you for the kind attention.
> > >
> > > Sidney.
> > 
> > If the A-190-2 was plugged in the wrong way the gate output is fried. In
> > this case the collector of the npn gate output transistor is connected
> > to -12V which destroys the transistor. This explains why the gate output
> > does not work anymore. It is difficult to say if other sections of the
> > module are defective too. You may try to replace the transistor (Q1,
> BC547C)
> > to see if this is the only defective part. Or you send in the module for
> > repair to the dealer where you purchased the device.
> > 
> > Best wishes
> > Dieter Doepfer
> >
> 
> 
> 
> 
> 
> [Non-text portions of this message have been removed]
>





[Non-text portions of this message have been removed]