Doepfer

Hello everyone!

I bought a nifty Analog Solutions delay/samper unit.  Very nice 
module.  One of the coolest parts of it is that you can control the 
sample start and sample end via CV.  

You can get neat effects by putting the sample playback on "loop" and 
keeping the sample start very close to the sample end - while sliding 
both forward and backward through the sample.  It sounds somewhat like 
granular synthesis.

However, it seems rather tricky to control both sample start and end 
and keep them both near each other.  I tried using two analog 
joysticks, but they weren't subtle enough and it was difficult to 
control.

Does anyone know of any module that can take a CV signal and add a 
very small voltage to it?  That way I could keep the sample end *just 
barely* past the sample start.

Thanks!
- Bret

Thanks!

I'll try using the 129/3 and see what happens!!

- Bret

--- In Doepfer_a100@yahoogroups.com, "unknown freak" <cgraef@n...> 
wrote:
> The A129/3 could do this, as could a mixer and A-176 CV source 
combination.
> 
> > -----Original Message-----
> > From: c45a6 [mailto:clone45@h...]
> > Sent: Sunday, September 21, 2003 2:21 PM
> > To: Doepfer_a100@yahoogroups.com
> > Subject: [Doepfer_a100] Strange sequencer question... small cv 
offsets.
> >
> >
> >
> > Hello everyone!
> >
> > I bought a nifty Analog Solutions delay/samper unit.  Very nice
> > module.  One of the coolest parts of it is that you can control 
the
> > sample start and sample end via CV.
> >
> > You can get neat effects by putting the sample playback on "loop" 
and
> > keeping the sample start very close to the sample end - while 
sliding
> > both forward and backward through the sample.  It sounds somewhat 
like
> > granular synthesis.
> >
> > However, it seems rather tricky to control both sample start and 
end
> > and keep them both near each other.  I tried using two analog
> > joysticks, but they weren't subtle enough and it was difficult to
> > control.
> >
> > Does anyone know of any module that can take a CV signal and add a
> > very small voltage to it?  That way I could keep the sample end 
*just
> > barely* past the sample start.
> >
> > Thanks!
> > - Bret
> >
> >
> >
> > To unsubscribe from this group, send an email to:
> > doepfer_a100-unsubscribe@yahoogroups.com
> >
> >
> >
> > Your use of Yahoo! Groups is subject to http://docs.yahoo.
com/info/terms/

> >
> >
> >

Wow!  Using the 129/3 worked great!  Thanks for the response!  What a 
great sound... and a new fancy use for the under-utilized 129/3 
(vocoder slew limiter).

- Bret

--- In Doepfer_a100@yahoogroups.com, "c45a6" <clone45@h...> wrote:
> Thanks!
> 
> I'll try using the 129/3 and see what happens!!
> 
> - Bret
> 
> --- In Doepfer_a100@yahoogroups.com, "unknown freak" <cgraef@n...> 
> wrote:
> > The A129/3 could do this, as could a mixer and A-176 CV source 
> combination.
> > 
> > > -----Original Message-----
> > > From: c45a6 [mailto:clone45@h...]
> > > Sent: Sunday, September 21, 2003 2:21 PM
> > > To: Doepfer_a100@yahoogroups.com
> > > Subject: [Doepfer_a100] Strange sequencer question... small cv 
> offsets.
> > >
> > >
> > >
> > > Hello everyone!
> > >
> > > I bought a nifty Analog Solutions delay/samper unit.  Very nice
> > > module.  One of the coolest parts of it is that you can control 
> the
> > > sample start and sample end via CV.
> > >
> > > You can get neat effects by putting the sample playback on 
"loop" 
> and
> > > keeping the sample start very close to the sample end - while 
> sliding
> > > both forward and backward through the sample.  It sounds 
somewhat 
> like
> > > granular synthesis.
> > >
> > > However, it seems rather tricky to control both sample start and 
> end
> > > and keep them both near each other.  I tried using two analog
> > > joysticks, but they weren't subtle enough and it was difficult 
to
> > > control.
> > >
> > > Does anyone know of any module that can take a CV signal and add 
a

> > > very small voltage to it?  That way I could keep the sample end 
> *just
> > > barely* past the sample start.
> > >
> > > Thanks!
> > > - Bret
> > >
> > >
> > >
> > > To unsubscribe from this group, send an email to:
> > > doepfer_a100-unsubscribe@yahoogroups.com
> > >
> > >
> > >
> > > Your use of Yahoo! Groups is subject to http://docs.yahoo.
> com/info/terms/
> > >
> > >
> > >

The A129/3 could do this, as could a mixer and A-176 CV source combination.

> -----Original Message-----
> From: c45a6 [mailto:clone45@hotmail.com]
> Sent: Sunday, September 21, 2003 2:21 PM
> To: Doepfer_a100@yahoogroups.com
> Subject: [Doepfer_a100] Strange sequencer question... small cv offsets.
>
>
>
> Hello everyone!
>
> I bought a nifty Analog Solutions delay/samper unit.  Very nice
> module.  One of the coolest parts of it is that you can control the
> sample start and sample end via CV.
>
> You can get neat effects by putting the sample playback on "loop" and
> keeping the sample start very close to the sample end - while sliding
> both forward and backward through the sample.  It sounds somewhat like
> granular synthesis.
>
> However, it seems rather tricky to control both sample start and end
> and keep them both near each other.  I tried using two analog
> joysticks, but they weren't subtle enough and it was difficult to
> control.
>
> Does anyone know of any module that can take a CV signal and add a
> very small voltage to it?  That way I could keep the sample end *just
> barely* past the sample start.
>
> Thanks!
> - Bret
>
>
>
> To unsubscribe from this group, send an email to:
> doepfer_a100-unsubscribe@yahoogroups.com
>
>
>
> Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
>
>
>