I think you have misunderstood what we are discussing, if you are doing a double sided board and a track is required to be connected under the device then you will need a pad. What would you connect the track to? If you have room you could add a via adjacent to the device pad but if not then you need a pad!
I don't suffer from insanity I enjoy it!
--- On Wed, 8/18/10, Bob Macklin <macklinbob@...> wrote:
From: Bob Macklin <macklinbob@...m>
Subject: Re: [Homebrew_PCBs] Re: Copper Foil Vias, Correct URL
To: Homebrew_PCBs@yahoogroups.com
Date: Wednesday, August 18, 2010, 5:35 PM
Don't put socket pads on the top side of boards. That's a really dumb thing
to do!
Bob Macklin
K5MYJ
Seattle, Wa.
"Real Radios Glow In The Dark"
----- Original Message -----
From: "Malcolm Parker-Lisberg" <mparkerlisberg@...>
To: <Homebrew_PCBs@yahoogroups.com>
Sent: Wednesday, August 18, 2010 9:13 AM
Subject: Re: [Homebrew_PCBs] Re: Copper Foil Vias, Correct URL
If you have a socket on the board you can't get at the top pad to solder it!
I don't suffer from insanity I enjoy it!
--- On Wed, 8/18/10, Bob Macklin <macklinbob@msn.com> wrote:
From: Bob Macklin <macklinbob@...>
Subject: Re: [Homebrew_PCBs] Re: Copper Foil Vias, Correct URL
To: Homebrew_PCBs@yahoogroups.com
Date: Wednesday, August 18, 2010, 4:23 PM
What's wrong with simply sticking a wire through the hole and
soldering on
both sides?
Bob Macklin
K5MYJ
Seattle, Wa.
"Real Radios Glow In The Dark"
----- Original Message -----
From: "Leon Heller" <leon355@...>
To: <Homebrew_PCBs@yahoogroups.com>
Sent: Wednesday, August 18, 2010 8:02 AM
Subject: Re: [Homebrew_PCBs] Re: Copper Foil Vias, Correct URL
> On 18/08/2010 15:00, Malcolm Parker-Lisberg wrote:
>> I tried that method back in the 1980s using a product called Circuitstick
>> and it is not worth the bother, much too fiddly and slow, difficult to
>> get a good solder joint between via copper and pad. It does give you a
>> through hole though. I found it much simpler to solder a thin strand of
>> copper to the top pad insert the device and solder both on the bottom. I
>> now just double up and provide an adjacent set of via pads where a
>> through via is needed on a component lead.
>
>
> Multicore used to sell little inserts that were pressed into the holes,
> flared with a special tool, and then soldered on both sides. They are
> probably still available.
>
> Leon
> --
> Leon Heller
> G1HSM
>
>
> ------------------------------------
>
> Be sure to visit the group home and check for new Links, Files, and
> Photos:
> http://groups.yahoo.com/group/Homebrew_PCBsYahoo! Groups Links
>
>
>
>
[Non-text portions of this message have been removed]
------------------------------------
Be sure to visit the group home and check for new Links, Files, and Photos:
http://groups.yahoo.com/group/Homebrew_PCBsYahoo! Groups Links
[Non-text portions of this message have been removed]Message
Re: [Homebrew_PCBs] Re: Copper Foil Vias, Correct URL
2010-08-18 by Malcolm Parker-Lisberg