QTR-Quadtone RIP

Hi Roy

I have done the test with paper size set to 17" but again to no avail.
I have also noticed that the printer is first pulling the paper back
in as it should and then it pushes it out again (as it shouldn't).

best regards & thanks
Juraj

--- In QuadtoneRIP@yahoogroups.com, "Roy Harrington" <roy@...> wrote:
>
> Hi Juraj,
> 
> I got your data -- all exactly correct.  It all confirms that you
are doing
> what I expected.
> 
> Eric reports that he's not had trouble with his 4800 and I have a
4000 which
> is very similar and
> not been a problem.  The only unusual thing I see in your case is
the 13inch
> paper and I
> imagine that this may be rarely used.  This being the problem seems
like a
> long shot but
> you never know.
> 
> I think you can work around this by making your paper size 17x9.5
instead of
> 13x9.5.
> Naturally you have to adjust the margins because of this and be sure
not to
> print off the
> paper.  The printer may also do a paper size check.  If you get a
error on
> the printer panel
> for this you can disable the check.  On the 4000 its under Menu >
Printer
> Setup > Paper Size Check.
> It's probably similar Just set it to OFF.
> 
> In your first post you mentioned that the printer is not pulling in
the roll
> before printing.  This is
> another good observation.  Continue to watch that in the tests.
> 
> Thanks,
> Roy
> 
> On Dec 4, 2007 9:41 AM, jurajlipscher <juraj@...> wrote:
> 
> >
> > Eric, thanks a lot for your help! I have CS 1 so there is no question
> > of CS 3 issues. My paper size (13 x 9.5") is set to the full width of
> > the 13" roll but my print is smaller than the roll dimensions (print
> > dimension = approx. 7 x 8") or in other words I do not print
> > borderless and do not have the "borderless" box checked in the driver
> > settings. As my print is smaller than the paper size I cannot have the
> > "to fit" box checked in QTR
> > I have just emailed Roy all the data he requested from me and hope
> > that the problem is going to be resolved - even more so seeing that
> > you do not experience any problems in this direction with the same
> > printer.
> >
> > Juraj
> >
> > --- In QuadtoneRIP@yahoogroups.com, "E Neilsen" <e.neilsen2@> wrote:
> > >
> > > Juraj, I just printed an image with my 4800 with roll cutter on. It
> > drew the
> > > paper back in just like it should both with CS3 direct and through
> > QTR. I
> > > used a 17" roll. The paper size was custom 17x14 as a portrait and
> > printed
> > > that way. I did have a "to fit" image box checked. You have the
> > borderless
> > > check box ticked in the properties for the Epson driver? As you are
> > using a
> > > 13" wide print on a 13" wide paper.
> > >
> > >
> > >
> > > Eric Neilsen Photo
> > >
> > > 4101 Commerce Street, Suite 9
> > >
> > > Dallas, TX 75226
> > >
> > > 214 827-8301
> > >
> > >
> > >
> > > http://ericneilsenphotography.com
> > >
> > > SKype ejprinter
> > >
> > >
> > >
> > >   _____
> > >
> > > From: QuadtoneRIP@yahoogroups.com
> > [mailto:QuadtoneRIP@yahoogroups.com] On
> > > Behalf Of jurajlipscher
> > > Sent: Monday, December 03, 2007 9:06 AM
> > > To: QuadtoneRIP@yahoogroups.com
> > > Subject: [QuadtoneRIP] Re: Wasting paper on a roll
> > >
> > >
> > >
> > > Hi Roy
> > >
> > > Thank you for your fast responses!! I am printing on a 13" roll in
> > > portrait orientation. My paper size is custom: width = 13" (the
whole
> > > width of the roll) and length = 9,45". So as far as I can see I
am not
> > > using too small a paper size and the orientation is correct too.
> > >
> > > I also tried to use the "banner roll" setting instead of "roll" with
> > > the option "save paper" turned on (in the WINDOWS settings for the
> > > 4800 printer) to no avail.
> > >
> > > Juraj
> > >
> > >
> > >
> > >
> > >
> > > [Non-text portions of this message have been removed]
> > >
> >
> >
> >
> >
> >
> > Yahoo! Groups Links
> >
> >
> >
> >
> 
> 
> [Non-text portions of this message have been removed]
>