QTR-Quadtone RIP

Unfortunately I have CS1 at home where only my 7000 resides. I don't have
any 13" rolls either so I can't try that either unless I just tell it that I
have 13" when I really have 17". That may not really help.

 

What dpi is your file? 360? And is this only happening with one image or any
image sized to 7x8?  However it really sounds more like a setting issue with
the printer. When I have the cutter OFF, there will be extra paper that
stays unprinted at the beginning of the roll. If I want to print close to
the edge, I put it in with the cutter set to ON, and then before printing on
canvas for example, I turn it off before sending the data to be printed.
Works fine. 

 

Eric Neilsen Photo

4101 Commerce Street, Suite 9

Dallas, TX 75226

214 827-8301

 

http://ericneilsenphotography.com

SKype ejprinter

 

  _____  

From: QuadtoneRIP@yahoogroups.com [mailto:QuadtoneRIP@yahoogroups.com] On
Behalf Of jurajlipscher
Sent: Tuesday, December 04, 2007 11:41 AM
To: QuadtoneRIP@yahoogroups.com
Subject: [QuadtoneRIP] Re: Wasting paper on a roll

 


Eric, thanks a lot for your help! I have CS 1 so there is no question
of CS 3 issues. My paper size (13 x 9.5") is set to the full width of
the 13" roll but my print is smaller than the roll dimensions (print
dimension = approx. 7 x 8") or in other words I do not print
borderless and do not have the "borderless" box checked in the driver
settings. As my print is smaller than the paper size I cannot have the
"to fit" box checked in QTR
I have just emailed Roy all the data he requested from me and hope
that the problem is going to be resolved - even more so seeing that 
you do not experience any problems in this direction with the same
printer.

Juraj

--- In QuadtoneRIP@ <mailto:QuadtoneRIP%40yahoogroups.com> yahoogroups.com,
"E Neilsen" <e.neilsen2@...> wrote:
>
> Juraj, I just printed an image with my 4800 with roll cutter on. It
drew the
> paper back in just like it should both with CS3 direct and through
QTR. I
> used a 17" roll. The paper size was custom 17x14 as a portrait and
printed
> that way. I did have a "to fit" image box checked. You have the
borderless
> check box ticked in the properties for the Epson driver? As you are
using a
> 13" wide print on a 13" wide paper. 
> 
> 
> 
> Eric Neilsen Photo
> 
> 4101 Commerce Street, Suite 9
> 
> Dallas, TX 75226
> 
> 214 827-8301
> 
> 
> 
> http://ericneilsenp <http://ericneilsenphotography.com> hotography.com
> 
> SKype ejprinter
> 
> 
> 
> _____ 
> 
> From: QuadtoneRIP@ <mailto:QuadtoneRIP%40yahoogroups.com> yahoogroups.com
[mailto:QuadtoneRIP@ <mailto:QuadtoneRIP%40yahoogroups.com> yahoogroups.com]
On
> Behalf Of jurajlipscher
> Sent: Monday, December 03, 2007 9:06 AM
> To: QuadtoneRIP@ <mailto:QuadtoneRIP%40yahoogroups.com> yahoogroups.com
> Subject: [QuadtoneRIP] Re: Wasting paper on a roll
> 
> 
> 
> Hi Roy
> 
> Thank you for your fast responses!! I am printing on a 13" roll in
> portrait orientation. My paper size is custom: width = 13" (the whole
> width of the roll) and length = 9,45". So as far as I can see I am not
> using too small a paper size and the orientation is correct too.
> 
> I also tried to use the "banner roll" setting instead of "roll" with
> the option "save paper" turned on (in the WINDOWS settings for the
> 4800 printer) to no avail.
> 
> Juraj
> 
> 
> 
> 
> 
> [Non-text portions of this message have been removed]
>

 



[Non-text portions of this message have been removed]