QTR-Quadtone RIP

Dear Roy

I have been printing with ABW/EPSON Driver for 2 years and I did not
have this problem. Recently I have installed K7 Piezo inks and QTR and
the problem started. Since the ink change I have used the same paper
size, the same print size and I did not use the EPSON driver at all.
And yes this happens every time.

I have not used the cutter off setting yet, this will be my next test.

Thanks again
Juraj

--- In QuadtoneRIP@yahoogroups.com, "Roy Harrington" <roy@...> wrote:
>
> I've done essentially the same thing on my 4000 and can't duplicate a
> problem.
> 
> Eric's idea about cutter ON/OFF on the printer may have merit.  Do
you use
> both cutter ON & OFF?  Are you changing the setting of this on the
printer
> panel?
> Also are you using the Epson driver immediately prior to QTR?
> 
> Have you done any other printing?  Sheet feeding? Other paper sizes?
> Does this always happen?
> 
> Roy
> 
> On Dec 4, 2007 1:55 PM, E Neilsen <e.neilsen2@...> wrote:
> 
> > Unfortunately I have CS1 at home where only my 7000 resides. I
don't have
> > any 13" rolls either so I can't try that either unless I just tell
it that
> > I
> > have 13" when I really have 17". That may not really help.
> >
> >
> >
> > What dpi is your file? 360? And is this only happening with one
image or
> > any
> > image sized to 7x8?  However it really sounds more like a setting
issue
> > with
> > the printer. When I have the cutter OFF, there will be extra paper
that
> > stays unprinted at the beginning of the roll. If I want to print
close to
> > the edge, I put it in with the cutter set to ON, and then before
printing
> > on
> > canvas for example, I turn it off before sending the data to be
printed.
> > Works fine.
> >
> >
> >
> > Eric Neilsen Photo
> >
> > 4101 Commerce Street, Suite 9
> >
> > Dallas, TX 75226
> >
> > 214 827-8301
> >
> >
> >
> > http://ericneilsenphotography.com
> >
> > SKype ejprinter
> >
> >
> >
> >  _____
> >
> > From: QuadtoneRIP@yahoogroups.com
[mailto:QuadtoneRIP@yahoogroups.com] On
> > Behalf Of jurajlipscher
> > Sent: Tuesday, December 04, 2007 11:41 AM
> > To: QuadtoneRIP@yahoogroups.com
> > Subject: [QuadtoneRIP] Re: Wasting paper on a roll
> >
> >
> >
> >
> > Eric, thanks a lot for your help! I have CS 1 so there is no question
> > of CS 3 issues. My paper size (13 x 9.5") is set to the full width of
> > the 13" roll but my print is smaller than the roll dimensions (print
> > dimension = approx. 7 x 8") or in other words I do not print
> > borderless and do not have the "borderless" box checked in the driver
> > settings. As my print is smaller than the paper size I cannot have the
> > "to fit" box checked in QTR
> > I have just emailed Roy all the data he requested from me and hope
> > that the problem is going to be resolved - even more so seeing that
> > you do not experience any problems in this direction with the same
> > printer.
> >
> > Juraj
> >
> > --- In QuadtoneRIP@ <mailto:QuadtoneRIP%40yahoogroups.com>
yahoogroups.com
> > ,
> > "E Neilsen" <e.neilsen2@> wrote:
> > >
> > > Juraj, I just printed an image with my 4800 with roll cutter on. It
> > drew the
> > > paper back in just like it should both with CS3 direct and through
> > QTR. I
> > > used a 17" roll. The paper size was custom 17x14 as a portrait and
> > printed
> > > that way. I did have a "to fit" image box checked. You have the
> > borderless
> > > check box ticked in the properties for the Epson driver? As you are
> > using a
> > > 13" wide print on a 13" wide paper.
> > >
> > >
> > >
> > > Eric Neilsen Photo
> > >
> > > 4101 Commerce Street, Suite 9
> > >
> > > Dallas, TX 75226
> > >
> > > 214 827-8301
> > >
> > >
> > >
> > > http://ericneilsenp <http://ericneilsenphotography.com>
hotography.com
> > >
> > > SKype ejprinter
> > >
> > >
> > >
> > > _____
> > >
> > > From: QuadtoneRIP@ <mailto:QuadtoneRIP%40yahoogroups.com>
> > yahoogroups.com
> > [mailto:QuadtoneRIP@ <mailto:QuadtoneRIP%40yahoogroups.com>
> > yahoogroups.com]
> > On
> > > Behalf Of jurajlipscher
> > > Sent: Monday, December 03, 2007 9:06 AM
> > > To: QuadtoneRIP@ <mailto:QuadtoneRIP%40yahoogroups.com>
yahoogroups.com
> > > Subject: [QuadtoneRIP] Re: Wasting paper on a roll
> > >
> > >
> > >
> > > Hi Roy
> > >
> > > Thank you for your fast responses!! I am printing on a 13" roll in
> > > portrait orientation. My paper size is custom: width = 13" (the
whole
> > > width of the roll) and length = 9,45". So as far as I can see I
am not
> > > using too small a paper size and the orientation is correct too.
> > >
> > > I also tried to use the "banner roll" setting instead of "roll" with
> > > the option "save paper" turned on (in the WINDOWS settings for the
> > > 4800 printer) to no avail.
> > >
> > > Juraj
> > >
> >
> >
> 
> 
> [Non-text portions of this message have been removed]
>