Analogue-sequencer

i 've made the  firmware UPDATE 3.006C after this V3.2CHK2B7C
>                                                 BOOT    FLASH

THEN I FLASH AND TRANSMIT ALL THE FILE(MORE DATA ON THE SCREEN). 
SCREEN ASK SIZE F180 THEN I BOOT BUT NOTHING HAPPENS I TRY A SECOND
TIME;NOTHING;PERHAPS THE VERSION 3.006B WHICH WAS INSTALLED?THANKS



> If it gets as far as that screen, the bootloader is working.
> It would be odd for the OS to be corrupt but not to show a checksum
error at
> boot.
> Try reloading the OS using firmware update mode - FUNC+PAGE at power on.
> 
> Best regards,
> Colin Fraser
> Sequentix Music Systems Ltd
> http://www.sequentix.com
> 
>  
> 
> > -----Original Message-----
> > From: analogue-sequencer@yahoogroups.com 
> > [mailto:analogue-sequencer@yahoogroups.com] On Behalf Of 
> > boops.secretvibes
> > Sent: 07 July 2008 23:02
> > To: analogue-sequencer@yahoogroups.com
> > Subject: [analogue-sequencer] Re: some help to finish my 
> > first P3 version 1.4
> > 
> > hi,Colin ,i put the chip version 1.6 on the main board 1.4,unluckly
> > the soft is freezing on this this screen     1/6 
> >                                              BANK FTS TUNE
> >  i 've tried F1+STEP 7 ,freeze again.
> >  i've tried to get off the battery memories always 1/6 
> >                                                    BANK FTS TUNE
> > 
> > any steps work...what can i do?:-( i 've maded this, cause i've got
> > always this tempo (moove alone) problem on the version
> > 1.4...nightmare..Best regards
> > 
> > 
> > 
> > 
> > 
> > --- In analogue-sequencer@yahoogroups.com, "boops.secretvibes"
> > <boops.secretvibes@> wrote:
> > >
> > > hi,thanks Colin for your informations..every seems alright for the
> > > moment...for the two P3(just  change a lcd connection ,and 
> > bootload)i
> > > must try midi and learn the manual..also 2 memX for me 
> > please(not just
> > > one as i 've written)Best regards..
> > > 
> > > 
> > > 
> > > - In analogue-sequencer@yahoogroups.com, "Colin Fraser" 
> > <colin@> wrote:
> > > >
> > > >  
> > > > > -hello,i 've finished today the 2ND main board P3 kit 1.6 with
> > > > > 3.006B,can i try it with my 1.4 others boards ,awaiting that i
> > > > > bootload the 1.4 chip ?i 've got always this tempo problem with
> > > > > this...work - no work (when i put my finger on the 3 pins of the
> > pot,
> > > > > working during a few seconds,ground problem?
> > > > 
> > > > There are two different clock speeds that the CPU may run at.
> > > > Pre-production P3s used an 18MHz crystal, production 
> > units used 24MHz.
> > > > As long as the crystal speed matches the CPU, you can use 
> > the later
> > > chips in
> > > > the early boards, and vice versa.
> > > > Each CPU has the crystal speed it is meant to run at stored in
> > > flash. The OS
> > > > adjusts to run at either speed by checking that setting.
> > > > 
> > > > Best regards,
> > > > Colin Fraser
> > > > Sequentix Music Systems Ltd
> > > > http://www.sequentix.com
> > > >
> > >
> > 
> > 
> > 
> > ------------------------------------
> > 
> > Yahoo! Groups Links
> > 
> > 
> >
>