Analogue-sequencer

I'm just about to ship this ready-built unit:
http://www.colinfraser.com/p3/gallery/p3-048.jpg
The font certainly looks more readable than the (cooler) Sci-fi font 
I normally use, so if you're buying a ready-built unit in the near 
future, remember to state your preference.
I'm hoping to get some more cases in as soon as Steve finds some 
time. The remaining few ready-built units assembled will be the type 
1 black/wide case until I get a custom made enclosure done. 

Cheers,
Colin f

How much will it cost?? Including shipping to the netherlands???

colinfraser_com <colin@colinfraser.com> wrote:I'm just about to ship this ready-built unit:
http://www.colinfraser.com/p3/gallery/p3-048.jpg
The font certainly looks more readable than the (cooler) Sci-fi font 
I normally use, so if you're buying a ready-built unit in the near 
future, remember to state your preference.
I'm hoping to get some more cases in as soon as Steve finds some 
time. The remaining few ready-built units assembled will be the type 
1 black/wide case until I get a custom made enclosure done. 

Cheers,
Colin f




Yahoo! Groups SponsorADVERTISEMENT


---------------------------------
Yahoo! Groups Links

   To visit your group on the web, go to:
http://groups.yahoo.com/group/analogue-sequencer/
  
   To unsubscribe from this group, send an email to:
analogue-sequencer-unsubscribe@yahoogroups.com
  
   Your use of Yahoo! Groups is subject to the Yahoo! Terms of Service. 



		
---------------------------------
Do you Yahoo!?
Yahoo! Mail is new and improved - Check it out!

[Non-text portions of this message have been removed]

I'm not sure what's going on.

Suddenly the p3 is cycling through parts 9=13 (well, part 1-4). I'm not sure
that I did anything to encourage this behavior. Turning it on and off has no
effect. I'm not sure how to stop this and get it just playing part 9 again.

I tried following the instructions in the manual but I'm getting nowhere. No
matter what I do (tried to change the chain at least from just 9-10, and it
seems to be working, but then the other parts light up again and it cycles
through all of them.)

No clue. Really don't feel like spending the rest of my weekend
troubleshooting and swearing.

ok, Gene, don't panic...I think I can help. Did you look at the release
notes document...it mentions a set pchain length aux event. Don't think it's
in the manual. Did you maybe set this event by mistake?

hmmm - looks like that's what happened. Fixed. Thanks, Gene.

No problem. Good thing I monitor this list pretty frequently.

> From: Gene Schwartz <implode7@comcast.net>
> Reply-To: analogue-sequencer@yahoogroups.com
> Date: Sun, 27 Jun 2004 19:38:14 -0700
> To: <analogue-sequencer@yahoogroups.com>
> Subject: [analogue-sequencer] help!
> 
> I'm not sure what's going on.
> 
> Suddenly the p3 is cycling through parts 9=13 (well, part 1-4). I'm not sure
> that I did anything to encourage this behavior. Turning it on and off has no
> effect. I'm not sure how to stop this and get it just playing part 9 again.
> 
> I tried following the instructions in the manual but I'm getting nowhere. No
> matter what I do (tried to change the chain at least from just 9-10, and it
> seems to be working, but then the other parts light up again and it cycles
> through all of them.)
> 
> No clue. Really don't feel like spending the rest of my weekend
> troubleshooting and swearing.
> 
> 
> 
> 
> 
> Yahoo! Groups Links
> 
> 
> 
> 
>