Bc2000 (for the BCF2000 & BCR2000)

hi,
I'd command panning with the bcf but I probably lost a step in the
various explanations.
the 01v96 pan  data string is:
left side $F0 $43 $10 $3E $7F $01 $1B $00 $00 $7F $7F $7F $41 $F7
center    $F0 $43 $10 $3E $7F $01 $1B $00 $00 $00 $00 $00 $00 $F7
right side$F0 $43 $10 $3E $7F $01 $1B $00 $00 $00 $00 $00 $3F $F7
 then
$encoder 1
  .showvalue on
  .mode 12dot
  .resolution 96 96 96 96
  .default 0
  .minmax 0 127
  .tx $F0 $43 $10 $3E $7F $01 $1B $00 $00 $7F $7F $7F val $F7
 and the pan work just half portion of course.
i
I've tray to change the variable but nothing.
where i mistake
i hope someone can explain 
all the best
Alessandro

--- In bc2000@yahoogroups.com, "Alessandro" <aledibox@...> wrote:
>
> hi,
> I'd command panning with the bcf but I probably lost a step in the
> various explanations.
> the 01v96 pan  data string is:
> left side $F0 $43 $10 $3E $7F $01 $1B $00 $00 $7F $7F $7F $41 $F7
> center    $F0 $43 $10 $3E $7F $01 $1B $00 $00 $00 $00 $00 $00 $F7
> right side$F0 $43 $10 $3E $7F $01 $1B $00 $00 $00 $00 $00 $3F $F7
>  then
> $encoder 1
>   .showvalue on
>   .mode 12dot
>   .resolution 96 96 96 96
>   .default 0
>   .minmax 0 127
>   .tx $F0 $43 $10 $3E $7F $01 $1B $00 $00 $7F $7F $7F val $F7
>  and the pan work just half portion of course.
> i
> I've tray to change the variable but nothing.
> where i mistake
> i hope someone can explain 
> all the best
> Alessandro
>

Hey - will attempt to give back here.
I think your .tx line should be.

.tx $F0 $43 $10 $3E $7F $01 $1B $00 $00 val12.13 val8.11 val4.7 val0.3 $F7

with the val commands listed above.

Try it.

Kip

HI Kip,

 the strings 

.tx $F0 $43 $10 $3E $7F $01 $1B $00 $00 val12.13 val8.11 val4.7 val0.3 $F7
 
work just from center  to rigth side.
 Please can you explain the string data? whay many different"valxx"?. 
tks

Alessandro

Hi Alessandro

> I'd command panning with the bcf but I probably lost a step in the
> various explanations.
> the 01v96 pan  data string is:
> left side $F0 $43 $10 $3E $7F $01 $1B $00 $00 $7F $7F $7F $41 $F7
> center    $F0 $43 $10 $3E $7F $01 $1B $00 $00 $00 $00 $00 $00 $F7
> right side$F0 $43 $10 $3E $7F $01 $1B $00 $00 $00 $00 $00 $3F $F7

$F0 $43 $10 $3E $7F $01 $1B $00 $00 $7F $7F $7F $41 $F7
$F0 $43 $10 $3E $7F $01 $1B $00 $00 $00 $00 $00 $00 $F7
$F0 $43 $10 $3E $7F $01 $1B $00 $00 $00 $00 $00 $3F $F7
Header ---------------------------- Data ----------
------------------------------------------------or checksum? (but it
couldn't be as the second and third lines are the same except fot the
checksum? byte)

Are you sure this is correct?
It looks very weird for a pan control.
How is it defined in the sysex specification? 



>  then
> $encoder 1
>   .showvalue on
>   .mode 12dot
>   .resolution 96 96 96 96
>   .default 0
>   .minmax 0 127

   .minmax  $41 0 ; for full left


Royce

>   .tx $F0 $43 $10 $3E $7F $01 $1B $00 $00 $7F $7F $7F val $F7
>  and the pan work just half portion of course.

> i
> I've tray to change the variable but nothing.
> where i mistake
> i hope someone can explain 
> all the best
> Alessandro
>