Doesn\ufffdt have the Perfomer a separate VCO for Brass? Ok, my Multiman had (afaik, i\ufffdve trashed it one Year ago, i\ufffdm sorry for the wrong Chip-Manufacturers/Types) -only- a TDA1008 and a replacement part (even the 1008 was defect) would have cost more than 40 Euro here. I currently own a Siel Cruise and it has a separate (VCO?) for the Mono-Section and a MK50240 for the Poly-Section. The Poly-Section also didn\ufffdt made any sound, only a quiet opamp-1shot- noise while pressing a key, but that wasn\ufffdt a Malfunction of the 50240; there was a 4066 nearly the TOG which was defect.... Stef Margus Kliimask wrote: >Hmm... From "and I don't think my string section is working..." I would >assume that the brass section IS working which would rule out the MK50240 >(then all notes would be dead). Concerning TDA1008 there's one per voice so >if one of them were dead you would lose just one note out of 12. As for >availability, TDA1008 is pretty easily available costing <$10. > >So if the brass section is working the critical stuff (SSM 2040 and SSM 2050 >in the later versions) are OK, the string section is just a bunch of 1458 >and 741 opamps. > >"also seems like the EQ switches don't do anything" - they shouldn't. EQ >only applies to string section. > >Best regards, >Margus > >-----Original Message----- >From: Stefan Rinass [mailto:st@...] >Sent: 27 December 2004 17:17 >To: crumar@yahoogroups.com >Subject: Re: [crumar] Re: Crumar Performer Question > > > >For me it seems that the Top Octave Generator (TDA1007 or SAA50240) is >defect. There are replacement parts for such Chips, but they cost much >money. > >Stef > >aaron_peters wrote: > > > >>Hi Ridzert, >> >>I'm using the Main output and the both Strings LEDs light up. The >>Strings volume is also turned up--no difference from the Brass >>setting--also seems like the EQ switches don't do anything. Thanks >>for the confirmation. Looks like I need to take it to the shop. >> >>Can anyone suggest a repair shop in the San Francisco Bay Area? >> >>Aaron >> >> >>--- In crumar@yahoogroups.com, ridzert van der zee <ridzertz@y...> >>wrote: >> >> >> >> >>>Hi Aaron, >>> >>>The Brass button doesn't have to be on! By pressing one/both of >>> >>> >>> >>> >>the Strings buttons you should here the string sound. >> >> >> >> >>>Which output do you use? Perhaps you accidentally used the >>> >>> >>> >>> >>seperate Brass output. >> >> >> >> >>>Do the LEDs (of the Stringsbuttons) light up when you push them? >>> >>> >>> >>> >>This could be an indicitation the buttons don't work. >> >> >> >> >>>The last option (is a stupid one, but just checking): Did you set >>> >>> >>> >>> >>the volume of the Strings section? >> >> >> >> >>>Cheers, >>> >>>Ridzert >>> >>> >>>aaron_peters <aaron_peters@y...> wrote: >>> >>>This might be dumb question, but does the Brass button have to be >>> >>> >>> >>> >>on >> >> >> >> >>>as well as one of the String buttons to get any string sounds out >>> >>> >>> >>> >>of >> >> >> >> >>>the Performer? Just pick up a used Performer and I don't think my >>>string section is working... >>> >>>Aaron >>> >>> >>> >>> >>>Yahoo! Groups SponsorADVERTISEMENT >>> >>> >>>--------------------------------- >>>Yahoo! Groups Links >>> >>> To visit your group on the web, go to: >>>http://groups.yahoo.com/group/crumar/ >>> >>> To unsubscribe from this group, send an email to: >>>crumar-unsubscribe@yahoogroups.com >>> >>> Your use of Yahoo! Groups is subject to the Yahoo! Terms of >>> >>> >>> >>> >>Service. >> >> >> >> >>> >>>--------------------------------- >>>Do you Yahoo!? >>>All your favorites on one personal page - Try My Yahoo! >>> >>> >>> >>> >> >> >> >> >> >>Yahoo! Groups Links >> >> >> >> >> >> >> >> >> >> >> >> > > > > > >Yahoo! Groups Links > > > > > > > > > > > >Yahoo! Groups Links > > > > > > > > > >
Message
Re: [crumar] Re: Crumar Performer Question
2004-12-27 by Stefan Rinass