Emax

i dont know if that card works as its the updated version i could not get it to work with the ensoniqs but the older version which is the pdf that you got did work with the ensoniqs and emax

that model does  work on yamaha a3000 kurzweil k2000/k2500 akais and rolands

the settings i use for the idsc 21-e are no jumpers on the fist 4 sets of pins 0-3 as this is id 0 which the emaxes can boot from

pin 4 and pin 5 need jumpers on this is for scsi 1 operation which is what the emaxes work at

pin 7 depending on what your ide to cf card supports pio mode is good enough for the emax as it only goes upto 600mb format size any way dma is for cards bigger than 1gb

check the cf card adapter to see what its set to if its a good quality 1 then you will have jumpers to set to dma /pio mode 

also the ide to cf adapter has to be set to master cant use slave as the scsi to ide wont read it 

no jumper on pin 9 as this puts it into flash rom mode and the device will not operate

can you post a picture of the cf card adapter


  ----- Original Message ----- 
  From: drifter7508 
  To: emax@yahoogroups.com 
  Sent: Sunday, February 07, 2010 1:28 PM
  Subject: [emax] Re: Point me to the places where to buy the right CF kit.


    


  SCSI TO IDE BRIDGE:
  http://cgi.ebay.de/ws/eBayISAPI.dll?ViewItem&item=330387956791&ssPageName=STRK:MEWNX:IT

  My settings at the moment:
  http://img59.imageshack.us/img59/9342/img0376x.jpg

  Jumper settings manual (I think):
  http://eab.abime.net/attachment.php?...8&d=1228279010

  --------------------------------------

  CF IDE READER CARD:
  http://cgi.ebay.de/ws/eBayISAPI.dll?ViewItem&item=180328325603&ssPageName=STRK:MEWAX:IT

  My settings at the moment:
  http://img62.imageshack.us/img62/1481/img0380p.jpg

  ----------------------------------

  Settings for my Panasonic SCSI CD (that would not work either)
  http://img59.imageshack.us/img59/762/img0374v.jpg

  --- In emax@yahoogroups.com, "jammie" <jammie.emma@...> wrote:
  >
  > what make and models did you buy first
  > 
  > what jumper settings are you using as this makes a big difference
  > 
  > what ide to cf card adapter are you using as some only support pio mode
  > 
  > and the scsi to ide needs to be set to this mode to work
  > 
  > the cf card that you got is fine they work
  > 
  > can you post pictures of set up as i can tell you what jumpers and settings 
  > to get it to work so can ted
  > ----- Original Message ----- 
  > From: "Brandt R. Gassman" <brandt@...>
  > To: <emax@yahoogroups.com>
  > Sent: Saturday, February 06, 2010 11:41 PM
  > Subject: Re: [emax] Re: Point me to the places where to buy the right CF 
  > kit.
  > 
  > 
  > > Ah, OK. I understand the situation now. Sorry if you've shared this
  > > information with the group already, but what external SCSI devices
  > > have you tried?
  > >
  > > The external SCSI > IDE > CF I'm using is the Spyrus MC-DISK2, which I
  > > purchased from scsiforsamplers.com in 2008 before they ran out. As
  > > noted, I successfully formatted two 1GB SanDisk CF cards with this
  > > unit (set to SCSI device #3). I've also used this device successfully
  > > with my Emulator III (set to device #5).
  > >
  > > Also, what type of Emax II do you have, and are you running the latest
  > > OS (2.14)? My Emax II was running 2.14 when I formatted the cards.
  > >
  > >
  > > On Feb 6, 2010, at 6:09 PM, drifter7508 wrote:
  > >
  > >> I have tried a bunch of different CF cards.
  > >> Most recently Sandisk 512 Mb oldschool
  > >> Dos fat 16 preform. cards. No luck.
  > >> The Emax wont even find the
  > >> units in the scsi connection. So I cant
  > >> format anything. :-(
  > >>
  > >> --- In emax@yahoogroups.com, "Brandt R. Gassman" <brandt@> wrote:
  > >> >
  > >> > What brand of CF cards are you using? How long are you allowing for
  > >> > the cards to format? I just successfully formatted two 1GB CF cards
  > >> > on an Emax II Turbo rack, but each card took about three hours to
  > >> > complete the "Verifying" process.
  > >> >
  > >> >
  > >> > On Feb 6, 2010, at 5:16 PM, drifter7508 wrote:
  > >> >
  > >> > > Isnt that exactly what I recently bought and
  > >> > > failed with? Not the same brand "Acard"
  > >> > > but exactly the same spec.
  > >> > >
  > >> > > I got 2 scsi cases allready. :)
  > >> > >
  > >> > > --- In emax@yahoogroups.com, "jammie" <jammie.emma@> wrote:
  > >> > > >
  > >> > > > you are going to find it hard now most kits have been sold buy a
  > >> > > acard 7720u scsi to ide adapter by an external scsi cdrom case
  > >> get a
  > >> > > ide to cf adapter try and get a atapi compliant so that it is hot
  > >> > > swappable
  > >> > > >
  > >> > > > and a 5.25"plate to 3.5" plate reducer for the 3.5" floppy size
  > >> > > ide to cf card drive this set up is going to cost you a bit so
  > >> shop
  > >> > > around on ebay for the scsi xternal cdrom case discard the cdrom
  > >> and
  > >> > > the scsi to ide interface
  > >> > > > ----- Original Message -----
  > >> > > > From: drifter7508
  > >> > > > To: emax@yahoogroups.com
  > >> > > > Sent: Saturday, February 06, 2010 9:20 PM
  > >> > > > Subject: [emax] Point me to the places where to buy the right CF
  > >> > > kit.
  > >> > > >
  > >> > > >
  > >> > > >
  > >> > > > So, Im fed up with all failures now.
  > >> > > >
  > >> > > > Can somebody please point me to a CF kit that actually 100%
  > >> > > > works with EMAX II.
  > >> > > >
  > >> > > > I would not like to buy a slim floppy and such, I'd rather
  > >> have a
  > >> > > > the CF kit installed in an external scsi case.
  > >> > > >
  > >> > > > Thx.
  > >> > > >
  > >> > > >
  > >> > > >
  > >> > > >
  > >> > > >
  > >> > > >
  > >> > > > ----------------------------------------------------------
  > >> > > >
  > >> > > >
  > >> > > >
  > >> > > > No virus found in this incoming message.
  > >> > > > Checked by AVG - www.avg.com
  > >> > > > Version: 8.5.435 / Virus Database: 271.1.1/2671 - Release Date:
  > >> > > 02/06/10 07:35:00
  > >> > > >
  > >> > > >
  > >> > > > [Non-text portions of this message have been removed]
  > >> > > >
  > >> > >
  > >> > >
  > >> > >
  > >> >
  > >> >
  > >> >
  > >> > [Non-text portions of this message have been removed]
  > >> >
  > >>
  > >>
  > >>
  > >
  > >
  > >
  > > [Non-text portions of this message have been removed]
  > >
  > >
  > >
  > > ------------------------------------
  > >
  > > Emax and Emax II User's Group Website
  > >
  > > http://www.silveriafamily.comYahoo! Groups Links
  > >
  > >
  > >
  > 
  > 
  > ----------------------------------------------------------
  > 
  > 
  > 
  > No virus found in this incoming message.
  > Checked by AVG - www.avg.com
  > Version: 8.5.435 / Virus Database: 271.1.1/2671 - Release Date: 02/06/10 
  > 07:35:00
  >



  


------------------------------------------------------------------------------



  No virus found in this incoming message.
  Checked by AVG - www.avg.com 
  Version: 8.5.435 / Virus Database: 271.1.1/2672 - Release Date: 02/06/10 19:35:00


[Non-text portions of this message have been removed]