Emax

what scsi to ide board do you have with the cfcard if its the rscsi-er then these are the new revision boards and they dont work

only the older revision boards do i told the guy from scsiforsamplers this was the case as he also sold them to ensoniq customers aswell and they did not work

the new boards dont have the 3volt drain termination like the older 1 these seem to be best for the scsi1 operation which the emax1/2 and ensoniqs use

those new boards work better in the akai,s and yamaha range of samplers

and the kurz k2000 and all later models the good thing about the new cards is there is no delay as there were on the acard cards and the older iodata cards

the acard atapi cards i got from ted if i can get them to read and write to the new atapi cf readers that i am working on then there will be a solution again and they are hot swappable they work with the new iodata cards so i can fit them into akais and yams and kurz and rolands they also work with the acard7720 which do work with the emax1/2
  ----- Original Message ----- 
  From: esynthesist 
  To: emax@yahoogroups.com 
  Sent: Sunday, April 18, 2010 3:36 PM
  Subject: [emax] Re: Using a CF-CARD from SCSIforSamplers with the Emax


    
  One other Emax user has responded via e-mail that he has exactly the same problems as me with the CF CARD on an Emax-I...

  ...SCSIForSamplers has removed the "Emax SE/HD" from the CF CARD compatibility list on their website now... 

  Anyone else who was (un)successful with the CF CARD on the Emax-I ?

  ///E-Synthesist

  --- In emax@yahoogroups.com, "esynthesist" <esynthesist@...> wrote:
  >
  > Hi 
  > 
  > I was wondering if anyone from the group is using a CF-CARD drive from SCSIforSamplers with his/her Emax-I ?
  > 
  > I have an external CF-CARD drive here which I recently ordered and it doesn't work with the Emax-I, although compatibility with Emax SE/HD is mentioned on the website of SCSIforSamplers. 
  > 
  > By the way: I ordered this drive specifically for my Ensoniq EPS, not for my Emax, but since it doesn't work with the EPS either, I'm trying to find out now on which samplers it would work. For now it's proven to be compatible with the Emax-II, the Emulator-III and the Emulator-IIIX.
  > 
  > While I can (and will) use Ted Summer's internal CF drive in my Emax-I as the primary solution, I'm still wondering why the CF-CARD drive is not working.
  > It formats the CF card, it even saves banks to the CF card, but it can't read these banks back. Very strange !
  > I always get a "Hard Disk Error" on both of my Emax samplers when loading banks from the CD CARD drive. Banks I just saved with the very same drive :) The CF cards that I'm using work fine with Ted's drive by the way.
  > 
  > So perhaps there may be an issue with the class or type of CF card in combination with that specific SCSIForSamplers drive.
  > If anyone is using the CF CARD drive succesfully with the Emax-I, I'd like to hear from you !!
  > 
  > Thanks in advance
  > 
  > ///E-Synthesist
  >



  


------------------------------------------------------------------------------



  No virus found in this incoming message.
  Checked by AVG - www.avg.com 
  Version: 8.5.437 / Virus Database: 271.1.1/2817 - Release Date: 04/17/10 18:31:00


[Non-text portions of this message have been removed]