Hello,
I've got some other problem with my C1 controller.
When I use the footswitch for activating particular preset then the unit "remembers" the state of the expression controller (instead of the value stored in the preset parameters) and for e.g. the volume increases to the full level while the presets are set to match the level between the presets. I opened the controller and clean the dust, I have done a complete reset of the GSP2101 and the problem persist. It does not happen all the time and I think (but I'm not sure) that not all of the presets reacts in this way. Lets say that when I change continuously between two presets then half time the volume matches the position of the footswitch instead of the written value. I also tried to connect an external expression pedal and the problem still has been present with a use of external pedal instead of the built-in one.
My unit is 3.00a/20 MHz, PPC installed. I have never experienced such problem before. Some time ago the whole unit has crashed and the hard reset was needed. The unit was then serviced and setup according to the information from Dieter's page (test procedures).
Before I have had a controller that was worn a lot and I have recently replaced it with the controller in as new condition. The controller worked fine for 2 months and recently the problem appeared.
Could you please advice?
Cheers,
Filip
www.myspace.com/hipgnosispl
Graham Pearson pisze:
Tom:\ufffdThere are 2 steps to using an expression pedal to control a program parameter.\ufffd You have performed only one step - pedal calibration.\ufffd The other step is to link the expression pedal to a program parameter.\ufffd Here's a copy of MIDIWizard's On-Line Help that describes this process:\ufffd\ufffdAssigning Control of a New Parameter to an Expression Pedal\ufffdFrom your program\u2019s title screen, use the [Previous] or [Next] arrow buttons and the function keys [1], [2], or [3] to select the parameter you wish to link to the expression pedal.\ufffd Next, press the [Link] button.\ufffd At this point, your 2101\u2019s LED displays the message \u201cSelect a Foot Switch\u201d.\ufffd Move your expression pedal to link it to the selected parameter.\ufffd Your 2101\u2019s LED confirms the new link.\ufffdPress function key [2] and use the DATA wheel to specify the parameter value corresponding to the full back toe-up pedal position.\ufffd Press function key [3] and use the DATA wheel to specify the parameter value corresponding to the full forward toe-down pedal position.\ufffdThe default values are the parameter\u2019s minimum and maximum values respectively.\ufffd If you want to invert the effect of your expression pedal, set the \u201cMin Value\u201d greater than the \u201cMax Value\u201d.\ufffdIt\u2019s usually difficult to know what minimum and maximum values you should select at this point.\ufffd After playing with the expression pedal for a while, you\u2019ll want to change these settings.\ufffd The help topic entitled \u201cChanging Minimum and Maximum Foot Switch or Expression Pedal Settings\u201d describes how to do this.\ufffdPress the [Link] button to exit the link menu.\ufffd Remember to press the [Store] button if you wish to save your updated program.\ufffd\ufffdDon't expect the expression pedal to control ANYTHING until you've performed the above process.\ufffd\ufffd\ufffd----- Original Message -----From: chingwaySent: Wednesday, July 23, 2008 3:01 PMSubject: Re: [gsp-2101] control pedal
I think so I mean I calibrated it according to the manual
On Tue, Jul 22, 2008 at 9:32 PM, Graham Pearson <me@grahampearson.com> wrote:
Tom:\ufffdAre you linking your pedal to the appropriate wah and pedal steel parameters, using the CC menu?\ufffd\ufffd----- Original Message -----From: earldoinkSent: Tuesday, July 22, 2008 8:17 PMSubject: [gsp-2101] control pedal
I'm having a problem with my expression pedal it lets me calibrate but
doesn't work with the wa or the pedal steel settings I've done the
resets and still no go any ideas??
tia
Tom