Hi, I just tried the same procedure and used the Flash ISP to load the code. I then used the AxD to load the debug symbols. Everything seems to be working fine. I can single step, run at full speed...etc If you have a small blinky application just send it to my email address and I can check it in my enviornment. amit --- In lpc2000@yahoogroups.com, "tah2k" <tah2k@y...> wrote: > > Multi-Ice autodetects the core based on the macrocell. It detects > ARM7TDMI-S ETM. This looks right to me. To verify memory contents, I > downloaded the flash image using Philips Flash Utility, and it > matches my code perfectly. > > --- In lpc2000@yahoogroups.com, "ian48harry" <ahi93@d...> wrote: > > > > Have you "told" Multi-ICE what chip you are dealing with? The > AT91 > > is plain ARM7TDMI, the LPC2000 is -S. Other tools allow specific > > selection of chips rather than basic core types. > > > > Ian > > > > --- In lpc2000@yahoogroups.com, "tah2k" <tah2k@y...> wrote: > > > > > > I understand where you are coming from, but I am trying to > prevent > > > buying more tools. From what I understand, the keil tools > require > > > their own emulator to actually run the debugger, and I already > have > > > 3 multi-ice. > > > > > > I am missing something, this should be trivial. If I reload the > > > blinky application, it works just fine. > > > > > > I have also got a keil mcb2100 board and I have the same issue. > > > > > > > > > --- In lpc2000@yahoogroups.com, "Dan Beadle" <dan.beadle@i...> > > wrote: > > > > I suggest you download the Keil tools. > > > > > > > > > > > > > > > > Download their demos. That will verify that everything is > > working > > > properly. > > > > > > > > > > > > > > > > > > > > From there, you could try the ARM tools with the Keil elf > > output. > > > At that > > > > point, you know that the board and the code are good. So you > > > would only be > > > > working one problem. > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > _____ > > > > > > > > From: tah2k [mailto:tah2k@y...] > > > > Sent: Monday, December 20, 2004 4:15 PM > > > > To: lpc2000@yahoogroups.com > > > > Subject: [lpc2000] Data Aborts > > > > > > > > > > > > > > > > > > > > Still not up and running with my Arm tools and the Keil > MCB2130. > > > > > > > > I setup the Arm AXD debugger to run the following script on > > > startup: > > > > > > > > loadsymbols C:\Projects\Sampler_2138 > \AppFlash\Output\AppFlash.axf > > > > setpc 0x0 > > > > sreg cpsr 0xd3 > > > > spp vector_catch 0 > > > > spp semihosting_enabled 0 > > > > > > > > It basically loads the debug symbols for the image in the 2138 > > > > flash, initializes the CPSR, sets the pc to 0, and disables > > > > breakpoints at the Arm exceptions. > > > > > > > > The debugger loads the source file correctly and the PC is set > at > > > > 0x0 which is a branch to my startup handler at 0x20. However, > if > > I > > > > run, or singlestep, or do anything, I get a "Data abort". > > > > > > > > Also, if I try and display memory starting at 0x0, the > debugger > > > > gives an error "Memory access failed" and only gives the > contents > > > of > > > > addresses 0-20, the rest 0's. > > > > > > > > I thought perhaps the data abort had something to do with the > > > > remapping done by the Philips boot loader, but I checked the > > > MEMMAP > > > > flag and it is set to 1, so I am running the flash at 0. > > > > > > > > I'm new to the part and evaluating it against the AT91 > pocessors, > > > > and I am fresh out of ideas. The memory bus is internal so its > > not > > > > like I can hook up my logic analyzer too get some ideas. > > > > > > > > Is it possible the Philips memory accelerator is partly to > blame? > > > > Tehre must be otehrs using Arm tools with this part so I am > > hoping > > > > it is something trivial. > > > > > > > > Any ideas are appreciated. > > > > Tim > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > Yahoo! Groups Sponsor > > > > > > > > > > > > > > > > ADVERTISEMENT > > > > > > > > > > > > > > <http://us.ard.yahoo.com/SIG=1297jigje/M=295196.4901138.6071305.30011 > > > 76/D=gr > > > > > > > > > > oups/S=1706554205:HM/EXP=1103674517/A=2128215/R=0/SIG=10se96mf6/*http > > > :/compa > > > > nion.yahoo.com> click here > > > > > > > > > > > > > > > > <http://us.adserver.yahoo.com/l? > > > M=295196.4901138.6071305.3001176/D=groups/S= > > > > :HM/A=2128215/rand=272492819> > > > > > > > > > > > > > > > > _____ > > > > > > > > Yahoo! Groups Links > > > > > > > > * To visit your group on the web, go to: > > > > http://groups.yahoo.com/group/lpc2000/ > > > > > > > > * To unsubscribe from this group, send an email to: > > > > lpc2000-unsubscribe@yahoogroups.com > > > > <mailto:lpc2000-unsubscribe@yahoogroups.com? > subject=Unsubscribe> > > > > > > > > * Your use of Yahoo! Groups is subject to the Yahoo! > > > > <http://docs.yahoo.com/info/terms/> Terms of Service. > > > > > > > > > > > > > > > > [Non-text portions of this message have been removed]
Message
Re: Data Aborts
2004-12-21 by Amit