Lpc2000

Thanks aumat123

i followed your advice and got the fault actualy SSEL pin was dry 
soldered.

Now i am trying to interface MMC card through SPI.

Jeetendra


--- In lpc2000@yahoogroups.com, "Jeetendra Singh" <jeet77_7@y...> 
wrote:
> 
> Yes i already Pulled up SSEL to 3v3 by a 47K Resister and not used 
> for CS(MMC_CS). I am using another GPIO for the purpose of CS 
> MMC_CS).     
> 
> Notice that In debugger i seen that after loading data in SPDR , 
SPIF 
> sets showing data transmited.
> 
> 
> --- In lpc2000@yahoogroups.com, "aumat123" <angelsp@a...> wrote:
> > 
> > You must pull up the SSEL of the SCI that you are using. Seem be 
> that 
> > the SCI in master mode need that the SSELx must be connected and 
> > pulled up externally for correct work.
> > 
> > 
> > --- In lpc2000@yahoogroups.com, "Mark Crow" <mcrow@p...> wrote:
> > > Is SSEL1 pulled up?
> > >   -----Original Message-----
> > >   From: Jeetendra Singh [mailto:jeet77_7@y...]
> > >   Sent: Friday, April 08, 2005 9:44 AM
> > >   To: lpc2000@yahoogroups.com
> > >   Subject: [lpc2000] spi in lpc2106
> > > 
> > > 
> > > 
> > >   Hi friends
> > > 
> > >   i am working in Lpc2106 and facing problem in spi mdule.
> > >   Actualy  i am using spi module in master mode. i checked my 
> code 
> > in
> > >   jtag debugger(wiggler in CrossStudio)and found that when 
> writing 
> > data
> > >   to the SPDR register then SPif bit in SPSR also sets showing 
> that
> > >   data is transmitted.
> > > 
> > >   But the problem is that nither data nor clocks in the MOSI & 
> SCK 
> > pins.
> > > 
> > > 
> > >   If some body can help me i will be very thank ful to him.
> > > 
> > >   jeetendra
> > > 
> > >   My source code attached
> > >   int main (void){
> > > 
> > > 
> > >         IOSET=0x80;
> > >         IODIR=0x00;
> > > 
> > >         PINSEL0 = 0x00005500;
> > > 
> > >   //Config over
> > >           init_spi();
> > > 
> > >           IOSET = MMC_CS; // Chip select High
> > >           MmCardSendByte(0xAA);
> > >           IOCLR = MMC_CS; // Chip select Low
> > > 
> > >           while (1);
> > >   }
> > > 
> > >   void init_spi(){
> > >       unsigned char ch;
> > > 
> > > 
> > >       IODIR |= MMC_CS; // io direction of mc chip select
> > >       IOSET = MMC_CS; // Chip select High
> > > 
> > >       SPCCR = 0xfe; // clock counter
> > >       SPCR =  0x20; // spi master mode,
> > > 
> > >   //   ch = SPDR;// data read
> > > 
> > >   }
> > > 
> > >   BYTE MmCardSendByte(BYTE bt)
> > >   {
> > >     BYTE input;
> > >     SPDR =  bt;
> > >     while (!(SPSR & 0x80));
> > >     input = SPDR;
> > > 
> > >     return input;
> > >   }
> > > 
> > > 
> > > 
> > > 
> > > 
> > > 
> > > ----------------------------------------------------------------
--
> --
> > --------
> > > --
> > >   Yahoo! Groups Links
> > > 
> > >     a.. To visit your group on the web, go to:
> > >     http://groups.yahoo.com/group/lpc2000/
> > > 
> > >     b.. To unsubscribe from this group, send an email to:
> > >     lpc2000-unsubscribe@yahoogroups.com
> > > 
> > >     c.. Your use of Yahoo! Groups is subject to the Yahoo! 
Terms 
> of 
> > Service.
> > > 
> > > 
> > > 
> > > [Non-text portions of this message have been removed]