Lpc2000

Gentleman,
I  am sharing my experience with J-Link, I hope it might help you to understand behaviour.

I had an issue with interrupts. My firmware works correctly (either in RAM of in flash.. I am using LPC2294 ...) when I power up the circuit  or provide reset by pressing reset switch on my Phytec development board.  When I am debugging  using J-Link, if I restart my program  without power up, my interupt does not work. I have a macro defined to provide reset to CPU but the reset provided by J-Link .... I do not get Reset pin going below 2V.... No reset actually occurs and this one creates the issue. I have tries same J-link on Atmel SAM7 series ARM7 development board , same problem, tried another J-link on both the board still same issue.... 
I did post this issue in this group earlier 
  ----- Original Message ----- 
  From: michael_rubinstein_sar 
  To: lpc2000@yahoogroups.com 
  Sent: Thursday, May 05, 2005 10:45 AM
  Subject: [lpc2000] Re: External Reset vs Power Up


  Hi Bob, thanks for the help.

  I'll bet you meant 1.31 (\TRST).  This signal is not connected on 
  our board.  However, it is driven high by the JTAG gizmo (J-Link).

  The other problems are really odd.  After an external reset, some of 
  the I/O pins just don't work.  I tried disconnecting 0.18 from other 
  circuitry, programming it as a gpio output and toggling it a few 
  times.  It works as expected after a power-up but just stays low 
  after an external reset.

  My code doesn't know the difference between a power-up reset and an 
  external reset.  I wonder if the ISP code behaves differently before 
  it transfers control to my code.

  Michael


  --- In lpc2000@yahoogroups.com, "lpc2100_fan" <lpc2100_fan@y...> 
  wrote:
  > Hello Michael,
  > 
  > one possible reason although this might not seem related.  If you 
  have
  > an external signal on pin 0.31 that would drive this pin low during
  > reset (no matter which reset), the LPC2138 will no longer enable 
  the
  > JTAG.  Please make sure that P0.31 not driven externally (has a 
  weak
  > pull-up) when any reset occurs. 
  > 
  > hth, Bob
  > 
  > 
  > 
  > --- In lpc2000@yahoogroups.com, "michael_rubinstein_sar"
  > <michael_rubinstein_sar@y...> wrote:
  > > I'm debugging a new 2138 based design.
  > > 
  > > If the board is powered up, eveything works as expected.  
  However, if 
  > > an external reset (\RESET) is then applied, several funny things 
  happen:
  > > 
  > > o  JTAG stops working.
  > > o  P0.18 which is configured as a timer capture input, sinks 
  current.
  > > o  P0.4 which is used as SPI SCK, in master mode, stops going 
  high.
  > > 
  > > I verified the values in PINSEL, IODIR and IOSET.  They are 
  correct and 
  > > the same in both cases.
  > > 
  > > Any help appreciated.
  > > 
  > > Thanks,
  > > Michael Rubinstein




------------------------------------------------------------------------------
  Yahoo! Groups Links

    a.. To visit your group on the web, go to:
    http://groups.yahoo.com/group/lpc2000/
      
    b.. To unsubscribe from this group, send an email to:
    lpc2000-unsubscribe@yahoogroups.com
      
    c.. Your use of Yahoo! Groups is subject to the Yahoo! Terms of Service. 



[Non-text portions of this message have been removed]