Lpc2000

Hello Leon,

Some info just from my memory and from dark archives so be carefull...

In the past I have used ocdremote for a few days and there were some 
issues with the different speeds. Below you find a snip from a message 
from that time.

'start of snip'
Strange enough you
need to do dummy connect to a RAVEN device first. This wil fail but it
leaves the interface in the correct state to connect properly for
WIGGLER. I am using now the next two commands and this works a lot
better (commands are for WIGGLER at LPT1)

ocdremote -cARM7TDMI-S -dRAVEN -a1 -s1   (results in Internal error 43)

ocdremote -cARM7TDMI-S -dWIGGLER -a1 -s1 (connects correctly)
'end of snip'

I was using your JTAG design so probably my info is completely useless 
for your situation.

At the moment I use the CrossWorks software from Rowley in combination 
with your JTAG design and this works very nice. (After replacing the 
buffer by a LVC device for 5V tolerant inputs)

Best Regards
Aalt


Leon Heller wrote:
> http://www.geocities.com/leon_heller
> ----- Original Message -----
> From: "Leon Heller" <leon.heller@...>
> To: <lpc2000@yahoogroups.com>
> Sent: Thursday, May 26, 2005 3:46 PM
> Subject: Re: [lpc2000] Amontec Chameleon
> 
> 
>  > ----- Original Message -----
>  > From: "Bill Knight" <BillK@...>
>  > To: <lpc2000@yahoogroups.com>
>  > Sent: Thursday, May 26, 2005 2:54 PM
>  > Subject: Re: [lpc2000] Amontec Chameleon
>  >
>  >
>  >> On Thu, 26 May 2005 14:40:01 +0100, Leon Heller wrote:
>  >>
>  >>>----- Original Message -----
>  >>>From: "Bill Knight" <BillK@...>
>  >>>To: <lpc2000@yahoogroups.com>
>  >>>Sent: Thursday, May 26, 2005 2:03 PM
>  >>>Subject: Re: [lpc2000] Amontec Chameleon
>  >>
>  >>
>  >>>> I've used it in both WIGGLER and Raven modes with the LPC.  I use an
>  >>>> older version of OCBLibRemote with the following command lines:
>  >>>>  OcdLibRemote.exe -c ARM7 -p 1000 -d WIGGLER -s 4
>  >>>> or
>  >>>>  OcdLibRemote.exe -c ARM7 -p 1000 -d RAVEN -s 4
>  >>>> The 's' param may be a bit slow but is the setting for the project on
>  >>>> which I am currently working.  I typically use the RAVEN mode except
>  >>>> when using CrossWorks which only supports the WIGGLER mode (they may
>  >>>> have
>  >>>> RAVEN mode now, not sure).  Also, the code for the Chameleon itsself
>  >>>> has
>  >>>> not
>  >>>> been updated from their web site in some time.
>  >>
>  >>>I'm using OCD Commander. I've downloaded OCDRemote for Windows and
>  >>>installed
>  >>>it, but can't run it and can't find the executable.
>  >>
>  >> IIRC it is in Cygwin\usr\local\bin
>  >> I usually create a Windows link to it in my project directory 
> setting the
>  >> parameters correctly, then just double-click it when it is needed.
>  >
>  > Sorry, I found it where you said.
>  >
>  > I'll see how I get on with it.
> 
> Same error (43) as with OCD Commander. I think I'll admit defeat and 
> give up
> trying to get it to work.
> 
> Leon
> 
> 
> 
> ------------------------------------------------------------------------
> *Yahoo! Groups Links*
> 
>     * To visit your group on the web, go to:
>       http://groups.yahoo.com/group/lpc2000/
>        
>     * To unsubscribe from this group, send an email to:
>       lpc2000-unsubscribe@yahoogroups.com
>       <mailto:lpc2000-unsubscribe@yahoogroups.com?subject=Unsubscribe>
>        
>     * Your use of Yahoo! Groups is subject to the Yahoo! Terms of
>       Service <http://docs.yahoo.com/info/terms/>. 
> 
> 

-- 
==============================
Aalt Lokhorst
Schut Geometrische Meettechniek bv
Duinkerkenstraat 21
9723 BN Groningen
P.O. Box 5225
9700 GE Groningen
The Netherlands
Tel: +31-50-5877877
Fax: +31-50-5877899
E-mail: Lokhorst@...
==============================