Lpc2000

----- Original Message ----- 
From: "Bill Knight" <BillK@...>
To: <lpc2000@yahoogroups.com>
Sent: Thursday, May 26, 2005 5:03 PM
Subject: Re: [lpc2000] Amontec Chameleon


> On Thu, 26 May 2005 15:56:37 +0100, Leon Heller wrote:
>
>>http://www.geocities.com/leon_heller
>>----- Original Message ----- 
>>From: "Leon Heller" <leon.heller@...>
>>To: <lpc2000@yahoogroups.com>
>>Sent: Thursday, May 26, 2005 3:46 PM
>>Subject: Re: [lpc2000] Amontec Chameleon
>
>
>>> ----- Original Message ----- 
>>> From: "Bill Knight" <BillK@...>
>>> To: <lpc2000@yahoogroups.com>
>>> Sent: Thursday, May 26, 2005 2:54 PM
>>> Subject: Re: [lpc2000] Amontec Chameleon
>>>
>>>
>>>> On Thu, 26 May 2005 14:40:01 +0100, Leon Heller wrote:
>>>>
>>>>>----- Original Message ----- 
>>>>>From: "Bill Knight" <BillK@...>
>>>>>To: <lpc2000@yahoogroups.com>
>>>>>Sent: Thursday, May 26, 2005 2:03 PM
>>>>>Subject: Re: [lpc2000] Amontec Chameleon
>>>>
>>>>
>>>>>> I've used it in both WIGGLER and Raven modes with the LPC.  I use an
>>>>>> older version of OCBLibRemote with the following command lines:
>>>>>>  OcdLibRemote.exe -c ARM7 -p 1000 -d WIGGLER -s 4
>>>>>> or
>>>>>>  OcdLibRemote.exe -c ARM7 -p 1000 -d RAVEN -s 4
>>>>>> The 's' param may be a bit slow but is the setting for the project on
>>>>>> which I am currently working.  I typically use the RAVEN mode except
>>>>>> when using CrossWorks which only supports the WIGGLER mode (they may
>>>>>> have
>>>>>> RAVEN mode now, not sure).  Also, the code for the Chameleon itsself
>>>>>> has
>>>>>> not
>>>>>> been updated from their web site in some time.
>>>>
>>>>>I'm using OCD Commander. I've downloaded OCDRemote for Windows and
>>>>>installed
>>>>>it, but can't run it and can't find the executable.
>>>>
>>>> IIRC it is in Cygwin\usr\local\bin
>>>> I usually create a Windows link to it in my project directory setting 
>>>> the
>>>> parameters correctly, then just double-click it when it is needed.
>>>
>>> Sorry, I found it where you said.
>>>
>>> I'll see how I get on with it.
>
>>Same error (43) as with OCD Commander. I think I'll admit defeat and give 
>>up
>>trying to get it to work.
>
> This SOUNDS like the error that newer versions of OcdLibRemote return
> when they find a non-standard WIGGLER.  I believe Macraigor's products
> have a jumper between a couple of the parallel port pins that the
> newer versions of code are checking.  I do not know if Amontec has
> added that functionality to the FPGA firmware.  Others on the mailing
> list might be able to confirm either or both.  If that is the problem,
> you could either acquire an older version of OcdLibRemote or build a
> db-25 adapter to add the jumper.

The link beween pins 8 and 15? That might be the cause of the problem. I'll 
remove it from my I/F and see if I get the same error.

Leon

Leon