Lpc2000

--- In lpc2000@yahoogroups.com, "eng_amrahmed3000" 
<eng_amrahmed3000@y...> wrote:
>
> Salam,
> 
> I did that but the problem is still exist :-(
> 
> Thanks
> 
> 
> --- In lpc2000@yahoogroups.com, Michael Johnson <mpj@r...> wrote:
> >
> > Hi,
> > 
> > Try setting the "Targets | Wiggler | Parallel Port Sharing" 
> property to 
> > be "Yes".
> > 
> > Regards
> > Michael
> > 
> > p.s. it may be worth sending CrossWorks support mails to 
> > support@r...
> > 
> > >Salam Again,
> > >
> > >Ok, Debugging is working fine.
> > >But i have encountered a strange behaviour.
> > >
> > >When i shut down crossworks and unplug the power supply, Then 
> > >connect it again and restart CrossWorks. CrossWorks didn't detect 
> > >the Wiggler Interface (20 PIN) unless i restart my PC to Works 
> > >again !!!
> > >
> > >What is the reason ?
> > >
> > >
> > >Eng. Amr Ahmed
> > >EGYPT
> > >
> > >--- In lpc2000@yahoogroups.com, "eng_amrahmed3000" 
> > ><eng_amrahmed3000@y...> wrote:
> > >  
> > >
> > >>********************************
> > >>THANKS VERY MUCH Michael Johnson
> > >>********************************
> > >>
> > >>I have set a breakpoint on the the start of my code and the 
> > >>debugging is working very well.
> > >>
> > >>:-)
> > >>
> > >>Eng. Amr Ahmed
> > >>EGYPT
> > >>
> > >>
> > >>
> > >>
> > >>--- In lpc2000@yahoogroups.com, Michael Johnson <mpj@r...> 
wrote:
> > >>    
> > >>
> > >>>Hi,
> > >>>
> > >>>Have you set a breakpoint anywhere? The 1.4 release didn't set 
> a 
> > >>>      
> > >>>
> > >>default 
> > >>    
> > >>
> > >>>breakpoint on main - the 1.5 release does.
> > >>>
> > >>>Michael
> > >>>
> > >>>      
> > >>>
> > >>>>Salam,
> > >>>>
> > >>>>The configuration under project options is "ARM Flash Debug" 
> > >>>>
> > >>>>What is the problem ?
> > >>>>
> > >>>>Thanks for your reply.
> > >>>>
> > >>>>Eng. Amr Ahmed
> > >>>>
> > >>>>--- In lpc2000@yahoogroups.com, Michael Johnson <mpj@r...> 
> > >>>>        
> > >>>>
> > >wrote:
> > >  
> > >
> > >>>> 
> > >>>>
> > >>>>        
> > >>>>
> > >>>>>Hi Amr,
> > >>>>>
> > >>>>>Do you have one of the "Debug" configurations selected 
> > >>>>>          
> > >>>>>
> > >e.g. "ARM 
> > >  
> > >
> > >>>>>   
> > >>>>>
> > >>>>>          
> > >>>>>
> > >>>>Flash 
> > >>>> 
> > >>>>
> > >>>>        
> > >>>>
> > >>>>>Debug".
> > >>>>>
> > >>>>>Regards
> > >>>>>Michael
> > >>>>>
> > >>>>>   
> > >>>>>
> > >>>>>          
> > >>>>>
> > >>>>>>Salam ALL,
> > >>>>>>
> > >>>>>>I have build Wiggler Interface succesfully.
> > >>>>>>I use CrossWorks for ARM 1.4.
> > >>>>>>
> > >>>>>>I can Compile my codes and choose Start Debugging.
> > >>>>>>The code works ok ( I can see on LEDs )
> > >>>>>>So The interface works perfectly to program and run the code 
> > >>>>>>     
> > >>>>>>
> > >>>>>>            
> > >>>>>>
> > >>>>using JTAG
> > >>>> 
> > >>>>
> > >>>>        
> > >>>>
> > >>>>>>But I can't use Step Into and similar debugging functions !
!!
> > >>>>>>
> > >>>>>>Please I need your help
> > >>>>>>
> > >>>>>>Best Regards,
> > >>>>>>Amr Ahmed
> > >>>>>>
> > >>>>>>
> > >>>>>>
> > >>>>>>		
> > >>>>>>---------------------------------
> > >>>>>>Yahoo! FareChase - Search multiple travel sites in one 
> > >>>>>>            
> > >>>>>>
> > >click.  
> > >  
> > >
> > >>>>>>[Non-text portions of this message have been removed]
> > >>>>>>
> > >>>>>>
> > >>>>>>
> > >>>>>>
> > >>>>>>
> > >>>>>>Yahoo! Groups Links
> > >>>>>>
> > >>>>>>
> > >>>>>>
> > >>>>>>
> > >>>>>>
> > >>>>>>
> > >>>>>>
> > >>>>>>
> > >>>>>>     
> > >>>>>>
> > >>>>>>            
> > >>>>>>
> > >>>>
> > >>>>
> > >>>>
> > >>>>
> > >>>>
> > >>>>
> > >>>>Yahoo! Groups Links
> > >>>>
> > >>>>
> > >>>>
> > >>>>
> > >>>>
> > >>>>
> > >>>> 
> > >>>>
> > >>>>        
> > >>>>
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > > 
> > >Yahoo! Groups Links
> > >
> > >
> > >
> > > 
> > >
> > >
> > >  
> > >
> >
>
Hi, 
 I think after power down/up you have to apply manual Reset to the  
board ( that is at least my experience with CrossWorks  and wiggler )
 Radim.