Boss VF-1 Effect Processor

Hi Cagan,

 

Thanks for the help!

 

After hours of reading the original manual and attempting to get an
expression pedal to work for volume, I almost gave up. Then, I downloaded
the current manual from the Behringer website. I followed the instructions
to calibrate the expression pedals and, immediately, expression pedal A
began working as a volume pedal.

 

Now, I’m hoping to figure out how to use expression pedal B as a toggle for
the tuner. So far, no luck. Have you tried this?

 

Thanks again,

 

David

 

  _____  

From: BossVF1@yahoogroups.com [mailto:BossVF1@yahoogroups.com] On Behalf Of
Çaðan CEBE
Sent: Tuesday, December 20, 2005 4:30 AM
To: BossVF1@yahoogroups.com
Subject: Re: [BossVF1] Anyone using a Behringer FCB101 with Boss VF-1?

 

Hi David,
I also use a fbc with my vf-1.

It is seems so complex at the beginning, but it is not
!
To use a pedal for expression,
-on vf-1, go to the master section of the patch in
question.
-select the related assign number (assign 1, 2 and
etc)
-select the target (wah manual, foot volume etc)
-target min and max should be 0 and 100
-do not select source type as exp pedal, you should
select the midi channel number here, like you said
mid-7. This is the main trick in here
-source mode should be normal
-source min and max should be 0 and 127

Now you should configure the fcb,
-you will either use 8th or 9th button-
-for related patch, you will select the related exp
pedal number by pushing it for 3 seconds in
configuration mode
-after the light comes, push once for editing the
parameters, this time the light blinks
-press "up" button once
-when number light blinks at the panel, you should
enter the midi channel number (same number that you
entered to vf-1)
-press "up" button again
-then "value" light blinks at panel
- you should enter the source min and max
consecutively same as you entered to vf-1
-after each section press "up" for saving parameters
-at the end press down for 3 secnds.


This is how I configure it out.

Regards...

Cagan




--- spangler1941 <spangler@...> wrote:

> I am trying to use a FCB1010 with a Boss VF-1 simply
> to switch banks,
> patches and control volume. So far it is baffling to
> me. Mainly need
> help how to configure the VF-1 to recognize an
> expression pedal on the
> FCB1010. I was doing fine with a Digitech Control 8
> and set the VF-1
> to MIDI 7 for the expression pedal in each patch.
> But I like the 10
> patch switches of the FCB1010 much better. Just need
> to get one of the
> expression pedals going.
> 
> Thanks, David Spangler in Texas
> 
> 
> 
> 
> 


__________________________________________________
Do You Yahoo!?
Tired of spam?  Yahoo! Mail has the best spam protection around 
http://mail.yahoo.com 



SPONSORED LINKS 


Effects
<http://groups.yahoo.com/gads?t=ms&k=Effects+processor&w1=Effects+processor&
c=1&s=23&.sig=onvvWZBJWA9SKnLgLNQeKA>  processor 

 

  _____  

YAHOO! GROUPS LINKS 

 

*	 Visit your group "BossVF1 <http://groups.yahoo.com/group/BossVF1> "
on the web.
  
*	 To unsubscribe from this group, send an email to:
 BossVF1-unsubscribe@yahoogroups.com
<mailto:BossVF1-unsubscribe@yahoogroups.com?subject=Unsubscribe> 
  
*	 Your use of Yahoo! Groups is subject to the Yahoo!
<http://docs.yahoo.com/info/terms/>  Terms of Service. 

 

  _____  



[Non-text portions of this message have been removed]