Yamaha DTXpress/DTXplorer/DTXtreme group photo

Yahoo Groups archive

Yamaha DTXpress/DTXplorer/DTXtreme

Index last updated: 2026-04-28 22:44 UTC

Thread

BP10 bar

BP10 bar

2001-04-24 by DrummerB0ui@aol.com

I know some of you out there are using the BP10 Dual Trigger bar. I need to know if there is a way to increase the output volume on the bar? I have set up voices on the bar but cannot get the volume to go loud enough to be heard through the PA system.

Any help would be greatly appreciated.

Scott

Re: [DTXpress] BP10 bar

2001-04-24 by Vivien Emiya

It's maybe a trigger problem. If the existant settings that you can chose in the trig menu(called BP) are not good, try to change the minimum velocity(MVel) in the trig menu but you will lose dynamics. Otherwise, increase the volume of your samples.You can put the volume of the channel 10 to the max in the song displayed below your kit name.
Does it work?
NB: Be carefull that there are no attenuation on the 9/10 entry. Maybe there is a mechanichal setting on your pad.
Show quoted textHide quoted text
----- Original Message -----
Sent: Tuesday, April 24, 2001 6:34 PM
Subject: [DTXpress] BP10 bar

I know some of you out there are using the BP10 Dual Trigger bar. I need to know if there is a way to increase the output volume on the bar? I have set up voices on the bar but cannot get the volume to go loud enough to be heard through the PA system.

Any help would be greatly appreciated.

Scott


Community email addresses:
Post message: DTXpress@onelist.com
Subscribe: DTXpress-subscribe@onelist.com
Unsubscribe: DTXpress-unsubscribe@onelist.com
List owner: DTXpress-owner@onelist.com

Shortcut URL to this page:
http://www.onelist.com/community/DTXpress

Your use of Yahoo! Groups is subject to the Yahoo! Terms of Service.

Re: [DTXpress] BP10 bar

2001-04-24 by Mark T. Owen

Check the tiny sensitivity switches on the back panel...
And you are right...the bar pads are less responsive overall.
I'm using a pintech bar pad and it works fine though I had to tweak the settings (as suggested by Vivien.)

Mark

Vivien Emiya wrote:

Show quoted textHide quoted text

It's maybe a trigger problem. If the existant settings that you can chose in the trig menu(called BP) are not good, try to change the minimum velocity(MVel) in the trig menu but you will lose dynamics. Otherwise, increase the volume of your samples.You can put the volume of the channel 10 to the max in the song displayed below your kit name.Does it work?NB: Be carefull that there are no attenuation on the 9/10 entry. Maybe there is a mechanichal setting on your pad.
----- Original Message -----
Sent: Tuesday, April 24, 2001 6:34 PM
Subject: [DTXpress] BP10 bar
�I know some of you out there are using the BP10 Dual Trigger bar. I need to know if there is a way to increase the output volume on the bar? I have set up voices on the bar but cannot get the volume to go loud enough to be heard through the PA system.

Any help would be greatly appreciated.

Scott
�

Community email addresses:
� Post message: DTXpress@onelist.com
� Subscribe:��� DTXpress-subscribe@onelist.com
� Unsubscribe:� DTXpress-unsubscribe@onelist.com
� List owner:�� DTXpress-owner@onelist.com

Shortcut URL to this page:
� http://www.onelist.com/community/DTXpress

Your use of Yahoo! Groups is subject to the Yahoo! Terms of Service.



Community email addresses:
� Post message: DTXpress@onelist.com
� Subscribe:��� DTXpress-subscribe@onelist.com
� Unsubscribe:� DTXpress-unsubscribe@onelist.com
� List owner:�� DTXpress-owner@onelist.com

Shortcut URL to this page:
� http://www.onelist.com/community/DTXpress

Your use of Yahoo! Groups is subject to the Yahoo! Terms of Service.

Re: [DTXpress] BP10 bar

2001-04-24 by Dan Mowczan

The BP10 does have a mechanical setting -- it is available via two screws
near the 1/4" jack on the side.  Check these adjustments.

-Dan

-- 
Dan Mowczan, pinball@...
Show quoted textHide quoted text
From: "Vivien Emiya" <vivien.emiya@...>
Reply-To: DTXpress@yahoogroups.com
Date: Tue, 24 Apr 2001 19:22:58 +0200
To: <DTXpress@yahoogroups.com>
Subject: Re: [DTXpress] BP10 bar


It's maybe a trigger problem. If the existant settings that you can chose in
the trig menu(called BP) are not good, try to change the minimum
velocity(MVel) in the trig menu but you will lose dynamics. Otherwise,
increase the volume of your samples.You can put the volume of the channel 10
to the max in the song displayed below your kit name.
Does it work?
NB: Be carefull that there are no attenuation on the 9/10 entry. Maybe there
is a mechanichal setting on your pad.
----- Original Message -----
From: DrummerB0ui@...
To: DTXpress@yahoogroups.com
Sent: Tuesday, April 24, 2001 6:34 PM
Subject: [DTXpress] BP10 bar

I know some of you out there are using the BP10 Dual Trigger bar. I need to
know if there is a way to increase the output volume on the bar? I have set
up voices on the bar but cannot get the volume to go loud enough to be heard
through the PA system.

Any help would be greatly appreciated.

Scott


Community email addresses:
 Post message: DTXpress@onelist.com
 Subscribe:    DTXpress-subscribe@onelist.com
 Unsubscribe:  DTXpress-unsubscribe@onelist.com
 List owner:   DTXpress-owner@onelist.com

Shortcut URL to this page:
 http://www.onelist.com/community/DTXpress

Your use of Yahoo! Groups is subject to the Yahoo! Terms of Service
<http://docs.yahoo.com/info/terms/> .

Yahoo! Groups Sponsor
Community email addresses:
 Post message: DTXpress@onelist.com
 Subscribe:    DTXpress-subscribe@onelist.com
 Unsubscribe:  DTXpress-unsubscribe@onelist.com
 List owner:   DTXpress-owner@onelist.com

Shortcut URL to this page:
 http://www.onelist.com/community/DTXpress

Your use of Yahoo! Groups is subject to the Yahoo! Terms of Service
<http://docs.yahoo.com/info/terms/> .

Move to quarantaine

This moves the raw source file on disk only. The archive index is not changed automatically, so you still need to run a manual refresh afterward.