Akai S1000 / S1100 samplers

Mattias,

I don't know if your cable is long enough to support the two drives. I
so, you could press another connector on the cable (if you're familiar
with that). 
Theoretically it is possible to extend the cable, but then you need to
make a scsi cable with two female and a male connector. As you know,
scsi is very sensitive and scsi adapters are easy to break.

Rgds

Frank




--- In akaiS1000S1100Samplers@yahoogroups.com, "koppeti"
<mathias_cedergren@h...> wrote:
> Hi,
> 
> Thanks for the jumper info. But, how do I connect the drives? Only 
> one connector is available on the SCSI cable, the other connector is 
> joined on the SCSI card by soldering. Are there any SCSI adapters or 
> cables out there extending the number of connectors? Is it possible 
> to integrate 68 pins cables, 50-to-68-pins adapters and so on?
> 
> If I manage to collect a service manual, I'll let you know!
> 
> Thanks.
> 
> 
> Regards,
> 
> Mattias
> 
> --- In akaiS1000S1100Samplers@yahoogroups.com, "formals777" 
> <frank.govaerts@p...> wrote:
> > Hi,
> > 
> > For connecting the internal scsi cable, there is not much you can do
> > wrong because the internal HD and the ZIP define their ID's through
> > the jumpers you will find on them. You know this works with a binary
> > system. Normally there are three jumpers: ID0, ID1 and ID2. Just 
> make
> > sure that they have a different id. 
> > The scsi cable should have a white mark on one side. That must be
> > aligned with pin 1 on the scsi connectors. 
> > 
> > I have never seen a service manual. 
> > 
> > Which other cables must be connected? Normally only the power supply
> > cables. Let us know. Someone on the list can supply you with some
> > pictures. 
> > 
> > Rgds
> > 
> > Frank 
> > 
> > 
> > --- In akaiS1000S1100Samplers@yahoogroups.com, "koppeti"
> > <mathias_cedergren@h...> wrote:
> > > Hi all,
> > > 
> > > First, I would like to say that this is a very nice community.
> > > 
> > > Now to my problems ... I recently decided to upgrade the 
> internal, 
> > > enormous 40MB hard drive of my S1000HD. At the same time I also 
> > > replaced the backlight panel and replaced the floppy drive with a 
> Zip 
> > > 100MB drive. So far, so good ... Now, I would like to reconnect 
> all 
> > > those disconnected cables (the way I labeled the cables turned 
> out to 
> > > be quite unsuccessful).
> > > 
> > > Does anyone know where I can find some service documentation or 
> > > schematics for the S1000? Even detailed photos of the interior 
> would 
> > > be great. I have not succeeded to get in touch with Akai here in 
> > > Sweden or with Akai in Japan.
> > > 
> > > The other problem: My S1000 is now equiped with two internal SCSI 
> > > drives. The internal SCSI cable only has two connectors, of which 
> one 
> > > is joined on the SCSI card by soldering. Does anyone have any 
> ideas 
> > > how to connect the drives?
> > > 
> > > Thank you very much.
> > > 
> > > 
> > > Regards,
> > > 
> > > Mattias, Sweden