Lpc2000

we can check the Buffer1_full bit is set or not after selecting the End
point.

anyway, thanks a lot.


-----Original Message-----
From: lpc2000@yahoogroups.com [mailto:lpc2000@yahoogroups.com]On Behalf
Of Manisha Kalita
Sent: Friday, April 07, 2006 8:22 PM
To: lpc2000@yahoogroups.com
Subject: [lpc2000] A new problem:: checking for data receive in USB
Endpoint


hi

the previous problem got solved. actually i was not checking the DataValid
bit,.

But, now, a new bug has come, the PKT_RDY is set only when interrupt is
enabled, however, in the spec i suppose, this is not mentioned anywhere. and
according to the design, i am using polling mode for data reception. so, can
anyone help me to check for data reception in polling?

thanks.

-----Original Message-----
From: lpc2000@yahoogroups.com [mailto:lpc2000@yahoogroups.com]On Behalf
Of ian.scanlon
Sent: Friday, April 07, 2006 7:33 PM
To: lpc2000@yahoogroups.com
Subject: [lpc2000] Re: Please help:: checking for data receive in USB
Endpoint


--- In lpc2000@yahoogroups.com, Manisha Kalita <manisha@...> wrote:
>
> can you give me the proper link for IAR code?
>
> about my code:
>
> /*Enable Read Mode and program the LOG_ENDPOINT High*/
> USB_CTRL = (DATA_TRANS_EP  << 2) | CTRL_RD_EN;
>
> & then i am checking for PKT_RDY bit as below.
> if (RX_PLENGTH & PKT_RDY)
> read the data.
>
>
> & here the if condition is always true. thats the main problem.
>
> regards,
> Manisha
>
>
> -----Original Message-----
> From: lpc2000@yahoogroups.com [mailto:lpc2000@yahoogroups.com]On
Behalf
> Of ian.scanlon
> Sent: Friday, April 07, 2006 7:13 PM
> To: lpc2000@yahoogroups.com
> Subject: [lpc2000] Re: Please help:: checking for data receive in
USB
> Endpoint
>
>
> --- In lpc2000@yahoogroups.com, Manisha Kalita <manisha@> wrote:
> >
> > ya its lpc 2148 board
> > ARM7 running at 60MHz, flash of 512 KB, RAM with 32 KB + 8 KB
> Shared with
> > USB DMA & USB 2.0 Device controller (Full Speed)DMA supported.
> using gcc. &
> > yes some help from sample code, i dont remeber the source.
> >
> > Regards,
> > Manisha
> >
> > -----Original Message-----
> > From: lpc2000@yahoogroups.com [mailto:lpc2000@yahoogroups.com]On
> Behalf
> > Of ian.scanlon
> > Sent: Friday, April 07, 2006 6:36 PM
> > To: lpc2000@yahoogroups.com
> > Subject: [lpc2000] Re: Please help:: checking for data receive in
> USB
> > Endpoint
> >
> >
> > --- In lpc2000@yahoogroups.com, Manisha Kalita <manisha@> wrote:
> > >
> > > Hi all,
> > >
> > > i am designing an USB driver in lpc2000 board.
> >
> > lpc2000 board?? what hardware? compiler? using example code from
> > ____? PC test application?
> >
> >
> >
> > it is sending the data
> > > properly. however, during reception, i am checking if any data
is
> > there in
> > > the deveice register RXPLENGTH. if there is any peacket, PKT-RDY
> > bit of this
> > > register is set. but, in my case, even though no data is sent
from
> > the host,
> > > PKT_RDY bit is always set. i am using interrupt transfer and so
> > using
> > > logical endpoint as 1.
> > >
>
> Can't really say why your code doesn't work, but the example code
> from Keil and IAR works well (mostly).
>
> Take a look at the IAR USB sample code. LPC_USB.c -> USB_EpRead
(...
> It is copyrighted so I won't post it here.  Did you write the Read
> enable bit?
>
>
>
>
>
>
>
>
>
> Yahoo! Groups Links
>
>
>
>
>
>
>
> The information contained in this electronic message and any
attachments to this message are intended for the exclusive use of the
addressee(s)and may contain confidential or privileged information.
If you are not the intended recipient, please notify the sender or
administrator@...
>


Look here for the IAR code.
http://www.olimex.com/dev/soft/arm/LPC/LPC2148_USB.zip

You will have to spend your own time at the IAR site or Keil site for
more.(www.IAR.com, www.keil.com)

I emailed you the IAR epRead function from IAR

-Ian









Yahoo! Groups Links







The information contained in this electronic message and any attachments to
this message are intended for the exclusive use of the addressee(s)and may
contain confidential or privileged information. If you are not the intended
recipient, please notify the sender or administrator@...



Yahoo! Groups Links







The information contained in this electronic message and any attachments to this message are intended for the exclusive use of the addressee(s)and may contain confidential or privileged information. If you are not the intended recipient, please notify the sender or administrator@...