Lpc2000

Hi,

To use JTAG debug on my EVBA7 with 2106 I also needed to remove JP12 to 
disable onboard (usb) debug.

Mike

At 09:50 05/04/2004, you wrote:
>"urn:schemas-microsoft-com:vml" xmlns:o = 
>"urn:schemas-microsoft-com:office:office" xmlns:w = 
>"urn:schemas-microsoft-com:office:word">
>Milos
>
>When I try to run the auto configure command, multi-ICE comes up with an 
>error message "Auto configuration Failed. Check the target power is on. 
>Your chip may require manual configuration"
>
>When I try to load it with the supplied configuration called single.cfg, 
>it tells me that there is an ARM7TDMI present, but when I run AXD I get a 
>message telling me that "The processor will not enter debug state when 
>requested" and I then receive subsequent messages while trying to force a 
>reset.
>
>On the EVAB7 I have
>JP6 (ENABLE SERIAL_ISP) removed
>JP11 (ENABLE PRIMARY DEBUG) inserted
>JP8 (SECONDARY DEBUG) removed
>
>Do I have to manually configure a target for Multi-ICE or should auto 
>configure work?
>
>Thanks
>Pauric
>
>-----Original Message-----
>From: Milos Prokic [mailto:mproki@...]
>Sent: 04 May 2004 17:23
>To: lpc2000@yahoogroups.com
>Subject: RE: [lpc2000] Ashling EVBA7 & ARM Multi-ICE
>
>Hi,
>
>I have setup the MultICE to work with the Ashling. I only had to remove 
>the jumper for on-board debug, and leave the jumper on primary debug, do 
>not switch it to the secondary. MultiICE detected the core without any 
>problems. Once the core was detected I was able to reset and run the AXD.
>
>Does multiICE see anything? Unknown device or something?
>
>Cheers,
>
>m.
>
>
>
>----------
>From: Pauric Doherty [mailto:pauric_doherty@...]
>Sent: Tuesday, May 04, 2004 12:20 PM
>To: lpc2000@yahoogroups.com
>Subject: [lpc2000] Ashling EVBA7 & ARM Multi-ICE
>
>
>
>All,
>
>
>
>I'm currently trying to get the ARM Multi-ICE unit to connect to the EVBA7 
>board from Ashling with an LCP2194 chip.
>
>I cannot get the multi-ICE unit to reset the chip. It won't even auto 
>detect it. I've followed the guide on how to enable the board for an 
>external debugger but still no luck.
>
>
>
>Has anyone tried the above situation .... or am I missing something obvious.
>
>
>
>Thanks in advance
>
>Pauric
>
>
>
>
>
>Yahoo! Groups Sponsor
>ADVERTISEMENT
><http://rd.yahoo.com/SIG=129gtjuh2/M=295196.4901138.6052515.3001176/D=groups/S=1706554205:HM/EXP=1083775489/A=2128215/R=0/SIG=10se96mf6/*http://companion.yahoo.com>
>click here
>
>[]
>
>
>
>----------
>Yahoo! Groups Links
>    * To visit your group on the web, go to:
>    * 
> <http://groups.yahoo.com/group/lpc2000/>http://groups.yahoo.com/group/lpc2000/
>    *
>    * To unsubscribe from this group, send an email to:
>    * 
> <mailto:lpc2000-unsubscribe@yahoogroups.com?subject=Unsubscribe>lpc2000-unsubscribe@yahoogroups.com 
>
>    *
>    * Your use of Yahoo! Groups is subject to the 
> <http://docs.yahoo.com/info/terms/>Yahoo! Terms of Service.