Yahoo Groups archive
Thread
2004-05-04 by Pauric Doherty
2004-05-04 by Milos Prokic
Hi, I have setup the MultICE to work with the Ashling. I only had to remove the jumper for on-board debug, and leave the jumper on primary debug, do not switch it to the secondary. MultiICE detected the core without any problems. Once the core was detected I was able to reset and run the AXD. Does multiICE see anything? Unknown device or something? Cheers, m. _____
From: Pauric Doherty [mailto:pauric_doherty@...] Sent: Tuesday, May 04, 2004 12:20 PM To: lpc2000@yahoogroups.com Subject: [lpc2000] Ashling EVBA7 & ARM Multi-ICE All, I'm currently trying to get the ARM Multi-ICE unit to connect to the EVBA7 board from Ashling with an LCP2194 chip. I cannot get the multi-ICE unit to reset the chip. It won't even auto detect it. I've followed the guide on how to enable the board for an external debugger but still no luck. Has anyone tried the above situation .... or am I missing something obvious. Thanks in advance Pauric Yahoo! Groups Sponsor ADVERTISEMENT <http://rd.yahoo.com/SIG=1297o90s7/M=295196.4901138.6052515.3001176/D=groups /S=1706554205:HM/EXP=1083773688/A=2128215/R=0/SIG=10se96mf6/*http:/companion .yahoo.com> click here <http://us.adserver.yahoo.com/l?M=295196.4901138.6052515.3001176/D=groups/S= :HM/A=2128215/rand=456273609> _____ Yahoo! Groups Links * To visit your group on the web, go to: http://groups.yahoo.com/group/lpc2000/ * To unsubscribe from this group, send an email to: lpc2000-unsubscribe@yahoogroups.com <mailto:lpc2000-unsubscribe@yahoogroups.com?subject=Unsubscribe> * Your use of Yahoo! Groups is subject to the Yahoo! <http://docs.yahoo.com/info/terms/> Terms of Service.
2004-05-04 by Pauric Doherty
Milos When I try to run the auto configure command, multi-ICE comes up with an error message "Auto configuration Failed. Check the target power is on. Your chip may require manual configuration" When I try to load it with the supplied configuration called single.cfg, it tells me that there is an ARM7TDMI present, but when I run AXD I get a message telling me that "The processor will not enter debug state when requested" and I then receive subsequent messages while trying to force a reset. On the EVAB7 I have JP6 (ENABLE SERIAL_ISP) removed JP11 (ENABLE PRIMARY DEBUG) inserted JP8 (SECONDARY DEBUG) removed Do I have to manually configure a target for Multi-ICE or should auto configure work? Thanks Pauric
-----Original Message-----
From: Milos Prokic [mailto:mproki@...]
Sent: 04 May 2004 17:23
To: lpc2000@yahoogroups.com
Subject: RE: [lpc2000] Ashling EVBA7 & ARM Multi-ICE
Hi,
I have setup the MultICE to work with the Ashling. I only had to remove
the jumper for on-board debug, and leave the jumper on primary debug, do not
switch it to the secondary. MultiICE detected the core without any problems.
Once the core was detected I was able to reset and run the AXD.
Does multiICE see anything? Unknown device or something?
Cheers,
m.
----------------------------------------------------------------------------
--
From: Pauric Doherty [mailto:pauric_doherty@...]
Sent: Tuesday, May 04, 2004 12:20 PM
To: lpc2000@yahoogroups.com
Subject: [lpc2000] Ashling EVBA7 & ARM Multi-ICE
All,
I'm currently trying to get the ARM Multi-ICE unit to connect to the EVBA7
board from Ashling with an LCP2194 chip.
I cannot get the multi-ICE unit to reset the chip. It won't even auto
detect it. I've followed the guide on how to enable the board for an
external debugger but still no luck.
Has anyone tried the above situation .... or am I missing something
obvious.
Thanks in advance
Pauric
Yahoo! Groups Sponsor
ADVERTISEMENT
----------------------------------------------------------------------------
--
Yahoo! Groups Links
a.. To visit your group on the web, go to:
http://groups.yahoo.com/group/lpc2000/
b.. To unsubscribe from this group, send an email to:
lpc2000-unsubscribe@yahoogroups.com
c.. Your use of Yahoo! Groups is subject to the Yahoo! Terms of Service.2004-05-04 by Michael Mathews
Hi, To use JTAG debug on my EVBA7 with 2106 I also needed to remove JP12 to disable onboard (usb) debug. Mike At 09:50 05/04/2004, you wrote:
>"urn:schemas-microsoft-com:vml" xmlns:o = >"urn:schemas-microsoft-com:office:office" xmlns:w = >"urn:schemas-microsoft-com:office:word"> >Milos > >When I try to run the auto configure command, multi-ICE comes up with an >error message "Auto configuration Failed. Check the target power is on. >Your chip may require manual configuration" > >When I try to load it with the supplied configuration called single.cfg, >it tells me that there is an ARM7TDMI present, but when I run AXD I get a >message telling me that "The processor will not enter debug state when >requested" and I then receive subsequent messages while trying to force a >reset. > >On the EVAB7 I have >JP6 (ENABLE SERIAL_ISP) removed >JP11 (ENABLE PRIMARY DEBUG) inserted >JP8 (SECONDARY DEBUG) removed > >Do I have to manually configure a target for Multi-ICE or should auto >configure work? > >Thanks >Pauric > >-----Original Message----- >From: Milos Prokic [mailto:mproki@...] >Sent: 04 May 2004 17:23 >To: lpc2000@yahoogroups.com >Subject: RE: [lpc2000] Ashling EVBA7 & ARM Multi-ICE > >Hi, > >I have setup the MultICE to work with the Ashling. I only had to remove >the jumper for on-board debug, and leave the jumper on primary debug, do >not switch it to the secondary. MultiICE detected the core without any >problems. Once the core was detected I was able to reset and run the AXD. > >Does multiICE see anything? Unknown device or something? > >Cheers, > >m. > > > >---------- >From: Pauric Doherty [mailto:pauric_doherty@...] >Sent: Tuesday, May 04, 2004 12:20 PM >To: lpc2000@yahoogroups.com >Subject: [lpc2000] Ashling EVBA7 & ARM Multi-ICE > > > >All, > > > >I'm currently trying to get the ARM Multi-ICE unit to connect to the EVBA7 >board from Ashling with an LCP2194 chip. > >I cannot get the multi-ICE unit to reset the chip. It won't even auto >detect it. I've followed the guide on how to enable the board for an >external debugger but still no luck. > > > >Has anyone tried the above situation .... or am I missing something obvious. > > > >Thanks in advance > >Pauric > > > > > >Yahoo! Groups Sponsor >ADVERTISEMENT ><http://rd.yahoo.com/SIG=129gtjuh2/M=295196.4901138.6052515.3001176/D=groups/S=1706554205:HM/EXP=1083775489/A=2128215/R=0/SIG=10se96mf6/*http://companion.yahoo.com> >click here > >[] > > > >---------- >Yahoo! Groups Links > * To visit your group on the web, go to: > * > <http://groups.yahoo.com/group/lpc2000/>http://groups.yahoo.com/group/lpc2000/ > * > * To unsubscribe from this group, send an email to: > * > <mailto:lpc2000-unsubscribe@yahoogroups.com?subject=Unsubscribe>lpc2000-unsubscribe@yahoogroups.com > > * > * Your use of Yahoo! Groups is subject to the > <http://docs.yahoo.com/info/terms/>Yahoo! Terms of Service.
2004-05-04 by Milos Prokic
Dohery, Make sure that JP12(On board debug) is also removed. I never had to load any config files, auto-detect worked right away. I guess you can't reset the hardware even when you use the config files, can you? My version of multiICE server is 2.1. As for the config files, are you talking about the ones supplied by the ARM (MultiICE) or something else? Regards, m. _____
From: Pauric Doherty [mailto:pauric_doherty@...] Sent: Tuesday, May 04, 2004 12:50 PM To: lpc2000@yahoogroups.com Subject: RE: [lpc2000] Ashling EVBA7 & ARM Multi-ICE Milos When I try to run the auto configure command, multi-ICE comes up with an error message "Auto configuration Failed. Check the target power is on. Your chip may require manual configuration" When I try to load it with the supplied configuration called single.cfg, it tells me that there is an ARM7TDMI present, but when I run AXD I get a message telling me that "The processor will not enter debug state when requested" and I then receive subsequent messages while trying to force a reset. On the EVAB7 I have JP6 (ENABLE SERIAL_ISP) removed JP11 (ENABLE PRIMARY DEBUG) inserted JP8 (SECONDARY DEBUG) removed Do I have to manually configure a target for Multi-ICE or should auto configure work? Thanks Pauric -----Original Message----- From: Milos Prokic [mailto:mproki@...] Sent: 04 May 2004 17:23 To: lpc2000@yahoogroups.com Subject: RE: [lpc2000] Ashling EVBA7 & ARM Multi-ICE Hi, I have setup the MultICE to work with the Ashling. I only had to remove the jumper for on-board debug, and leave the jumper on primary debug, do not switch it to the secondary. MultiICE detected the core without any problems. Once the core was detected I was able to reset and run the AXD. Does multiICE see anything? Unknown device or something? Cheers, m. _____ From: Pauric Doherty [mailto:pauric_doherty@...] Sent: Tuesday, May 04, 2004 12:20 PM To: lpc2000@yahoogroups.com Subject: [lpc2000] Ashling EVBA7 & ARM Multi-ICE All, I'm currently trying to get the ARM Multi-ICE unit to connect to the EVBA7 board from Ashling with an LCP2194 chip. I cannot get the multi-ICE unit to reset the chip. It won't even auto detect it. I've followed the guide on how to enable the board for an external debugger but still no luck. Has anyone tried the above situation .... or am I missing something obvious. Thanks in advance Pauric Yahoo! Groups Sponsor ADVERTISEMENT <http://rd.yahoo.com/SIG=129gtjuh2/M=295196.4901138.6052515.3001176/D=groups /S=1706554205:HM/EXP=1083775489/A=2128215/R=0/SIG=10se96mf6/*http:/companion .yahoo.com> click here <http://us.adserver.yahoo.com/l?M=295196.4901138.6052515.3001176/D=groups/S= :HM/A=2128215/rand=819205855> _____ Yahoo! Groups Links * To visit your group on the web, go to: http://groups.yahoo.com/group/lpc2000/ * To unsubscribe from this group, send an email to: lpc2000-unsubscribe@yahoogroups.com <mailto:lpc2000-unsubscribe@yahoogroups.com?subject=Unsubscribe> * Your use of Yahoo! Groups is subject to the Yahoo! <http://docs.yahoo.com/info/terms/> Terms of Service.
2004-05-04 by Milos Prokic
Hi Mike, I wanted to ask you if you were able to download programs to flash and debug them using AXD through MultiICE. I can easily work my s/w from RAM but since my project is getting bigger every day I need to move some libraries into FLASH. I want to instruct the linker to create several object files that I can place in RAM or FLASH. For example have the f/w drivers, OS be in FLASH while I only run code that I'm working on from RAM. I was wondering if it is possible, and if it is how would one go about it. Thanks in advance, m. _____
From: Michael Mathews [mailto:mmathews@...] Sent: Tuesday, May 04, 2004 1:09 PM To: lpc2000@yahoogroups.com Subject: RE: [lpc2000] Ashling EVBA7 & ARM Multi-ICE Hi, To use JTAG debug on my EVBA7 with 2106 I also needed to remove JP12 to disable onboard (usb) debug. Mike At 09:50 05/04/2004, you wrote: "urn:schemas-microsoft-com:vml" xmlns:o = "urn:schemas-microsoft-com:office:office" xmlns:w = "urn:schemas-microsoft-com:office:word"> Milos When I try to run the auto configure command, multi-ICE comes up with an error message "Auto configuration Failed. Check the target power is on. Your chip may require manual configuration" When I try to load it with the supplied configuration called single.cfg, it tells me that there is an ARM7TDMI present, but when I run AXD I get a message telling me that "The processor will not enter debug state when requested" and I then receive subsequent messages while trying to force a reset. On the EVAB7 I have JP6 (ENABLE SERIAL_ISP) removed JP11 (ENABLE PRIMARY DEBUG) inserted JP8 (SECONDARY DEBUG) removed Do I have to manually configure a target for Multi-ICE or should auto configure work? Thanks Pauric -----Original Message----- From: Milos Prokic [mailto:mproki@...] Sent: 04 May 2004 17:23 To: lpc2000@yahoogroups.com Subject: RE: [lpc2000] Ashling EVBA7 & ARM Multi-ICE Hi, I have setup the MultICE to work with the Ashling. I only had to remove the jumper for on-board debug, and leave the jumper on primary debug, do not switch it to the secondary. MultiICE detected the core without any problems. Once the core was detected I was able to reset and run the AXD. Does multiICE see anything? Unknown device or something? Cheers, m. _____ From: Pauric Doherty [mailto:pauric_doherty@...] Sent: Tuesday, May 04, 2004 12:20 PM To: lpc2000@yahoogroups.com Subject: [lpc2000] Ashling EVBA7 & ARM Multi-ICE All, I'm currently trying to get the ARM Multi-ICE unit to connect to the EVBA7 board from Ashling with an LCP2194 chip. I cannot get the multi-ICE unit to reset the chip. It won't even auto detect it. I've followed the guide on how to enable the board for an external debugger but still no luck. Has anyone tried the above situation .... or am I missing something obvious. Thanks in advance Pauric Yahoo! Groups Sponsor ADVERTISEMENT <http://rd.yahoo.com/SIG=129gtjuh2/M=295196.4901138.6052515.3001176/D=groups /S=1706554205:HM/EXP=1083775489/A=2128215/R=0/SIG=10se96mf6/*http:/companion .yahoo.com> click here [] <http://us.adserver.yahoo.com/l?M=295196.4901138.6052515.3001176/D=groups/S= :HM/A=2128215/rand=819205855> _____ Yahoo! Groups Links * To visit your group on the web, go to: * http://groups.yahoo.com/group/lpc2000/ * * To unsubscribe from this group, send an email to: * lpc2000-unsubscribe@yahoogroups.com <mailto:lpc2000-unsubscribe@yahoogroups.com?subject=Unsubscribe> * * Your use of Yahoo! Groups is subject to the Yahoo! <http://docs.yahoo.com/info/terms/> Terms of Service. _____ Yahoo! Groups Links * To visit your group on the web, go to: http://groups.yahoo.com/group/lpc2000/ * To unsubscribe from this group, send an email to: lpc2000-unsubscribe@yahoogroups.com <mailto:lpc2000-unsubscribe@yahoogroups.com?subject=Unsubscribe> * Your use of Yahoo! Groups is subject to the Yahoo! <http://docs.yahoo.com/info/terms/> Terms of Service.
2004-05-04 by Richard
Remove JP6 (ISP entry) --- In lpc2000@yahoogroups.com, "Milos Prokic" <mproki@m...> wrote: > Dohery, > > Make sure that JP12(On board debug) is also removed. > > I never had to load any config files, auto-detect worked right away. I guess > you can't reset the hardware even when you use the config files, can you? > > My version of multiICE server is 2.1. > > As for the config files, are you talking about the ones supplied by the ARM > (MultiICE) or something else? > > Regards, > > m. > > > > _____ > > From: Pauric Doherty [mailto:pauric_doherty@y...] > Sent: Tuesday, May 04, 2004 12:50 PM > To: lpc2000@yahoogroups.com > Subject: RE: [lpc2000] Ashling EVBA7 & ARM Multi-ICE > > > > Milos > > > > When I try to run the auto configure command, multi-ICE comes up with an > error message "Auto configuration Failed. Check the target power is on. Your > chip may require manual configuration" > > > > When I try to load it with the supplied configuration called single.cfg, it > tells me that there is an ARM7TDMI present, but when I run AXD I get a > message telling me that "The processor will not enter debug state when > requested" and I then receive subsequent messages while trying to force a > reset. > > > > On the EVAB7 I have > > JP6 (ENABLE SERIAL_ISP) removed > > JP11 (ENABLE PRIMARY DEBUG) inserted > > JP8 (SECONDARY DEBUG) removed > > > > Do I have to manually configure a target for Multi-ICE or should auto > configure work? > > > > Thanks > > Pauric > > > > -----Original Message----- > From: Milos Prokic [mailto:mproki@m...] > Sent: 04 May 2004 17:23 > To: lpc2000@yahoogroups.com > Subject: RE: [lpc2000] Ashling EVBA7 & ARM Multi-ICE > > Hi, > > I have setup the MultICE to work with the Ashling. I only had to remove the > jumper for on-board debug, and leave the jumper on primary debug, do not > switch it to the secondary. MultiICE detected the core without any problems. > Once the core was detected I was able to reset and run the AXD. > > Does multiICE see anything? Unknown device or something? > > Cheers, > > m. > > > > > _____ > > > From: Pauric Doherty [mailto:pauric_doherty@y...] > Sent: Tuesday, May 04, 2004 12:20 PM > To: lpc2000@yahoogroups.com > Subject: [lpc2000] Ashling EVBA7 & ARM Multi-ICE > > > > All, > > > > I'm currently trying to get the ARM Multi-ICE unit to connect to the EVBA7 > board from Ashling with an LCP2194 chip. > > I cannot get the multi-ICE unit to reset the chip. It won't even auto detect > it. I've followed the guide on how to enable the board for an external > debugger but still no luck. > > > > Has anyone tried the above situation .... or am I missing something obvious. > > > > Thanks in advance > > Pauric > > > > > > > > > > > Yahoo! Groups Sponsor > > > > ADVERTISEMENT > > <http://rd.yahoo.com/SIG=129gtjuh2/M=295196.4901138.6052515.3001176/D= groups > /S=1706554205:HM/EXP=1083775489/A=2128215/R=0/SIG=10se96mf6/*http:/c ompanion > .yahoo.com> click here > > > > <http://us.adserver.yahoo.com/l? M=295196.4901138.6052515.3001176/D=groups/S=
> :HM/A=2128215/rand=819205855> > > > > _____ > > Yahoo! Groups Links > > * To visit your group on the web, go to: > http://groups.yahoo.com/group/lpc2000/ > > * To unsubscribe from this group, send an email to: > lpc2000-unsubscribe@yahoogroups.com > <mailto:lpc2000-unsubscribe@yahoogroups.com?subject=Unsubscribe> > > * Your use of Yahoo! Groups is subject to the Yahoo! > <http://docs.yahoo.com/info/terms/> Terms of Service.