Lpc2000

Remove JP6 (ISP entry)

--- In lpc2000@yahoogroups.com, "Milos Prokic" <mproki@m...> wrote:
> Dohery,
> 
> Make sure that JP12(On board debug) is also removed. 
> 
> I never had to load any config files, auto-detect worked right 
away. I guess
> you can't reset the hardware even when you use the config files, 
can you?
> 
> My version of multiICE server is 2.1.
> 
> As for the config files, are you talking about the ones supplied by 
the ARM
> (MultiICE) or something else?
> 
> Regards,
> 
> m. 
> 
>  
> 
>   _____  
> 
> From: Pauric Doherty [mailto:pauric_doherty@y...] 
> Sent: Tuesday, May 04, 2004 12:50 PM
> To: lpc2000@yahoogroups.com
> Subject: RE: [lpc2000] Ashling EVBA7 & ARM Multi-ICE
> 
>  
> 
> Milos
> 
>  
> 
> When I try to run the auto configure command, multi-ICE comes up 
with an
> error message "Auto configuration Failed. Check the target power is 
on. Your
> chip may require manual configuration"
> 
>  
> 
> When I try to load it with the supplied configuration called 
single.cfg, it
> tells me that there is an ARM7TDMI present, but when I run AXD I 
get a
> message telling me that "The processor will not enter debug state 
when
> requested" and I then receive subsequent messages while trying to 
force a
> reset.
> 
>  
> 
> On the EVAB7 I have 
> 
> JP6 (ENABLE SERIAL_ISP) removed
> 
> JP11 (ENABLE PRIMARY DEBUG) inserted
> 
> JP8 (SECONDARY DEBUG) removed
> 
>  
> 
> Do I have to manually configure a target for Multi-ICE or should 
auto
> configure work?
> 
>  
> 
> Thanks
> 
> Pauric
> 
>  
> 
> -----Original Message-----
> From: Milos Prokic [mailto:mproki@m...]
> Sent: 04 May 2004 17:23
> To: lpc2000@yahoogroups.com
> Subject: RE: [lpc2000] Ashling EVBA7 & ARM Multi-ICE
> 
> Hi,
> 
> I have setup the MultICE to work with the Ashling. I only had to 
remove the
> jumper for on-board debug, and leave the jumper on primary debug, 
do not
> switch it to the secondary. MultiICE detected the core without any 
problems.
> Once the core was detected I was able to reset and run the AXD.
> 
> Does multiICE see anything? Unknown device or something? 
> 
> Cheers,
> 
> m.
> 
>  
> 
> 
>   _____  
> 
> 
> From: Pauric Doherty [mailto:pauric_doherty@y...] 
> Sent: Tuesday, May 04, 2004 12:20 PM
> To: lpc2000@yahoogroups.com
> Subject: [lpc2000] Ashling EVBA7 & ARM Multi-ICE
> 
>  
> 
> All,
> 
>  
> 
> I'm currently trying to get the ARM Multi-ICE unit to connect to 
the EVBA7
> board from Ashling with an LCP2194 chip. 
> 
> I cannot get the multi-ICE unit to reset the chip. It won't even 
auto detect
> it. I've followed the guide on how to enable the board for an 
external
> debugger but still no luck.
> 
>  
> 
> Has anyone tried the above situation .... or am I missing something 
obvious.
> 
>  
> 
> Thanks in advance
> 
> Pauric
> 
>  
> 
>  
> 
> 
> 
> 
> 
> 
> Yahoo! Groups Sponsor
> 
> 
> 
> ADVERTISEMENT
>  
> 
<http://rd.yahoo.com/SIG=129gtjuh2/M=295196.4901138.6052515.3001176/D=
groups
> /S=1706554205:HM/EXP=1083775489/A=2128215/R=0/SIG=10se96mf6/*http:/c
ompanion
> .yahoo.com> click here
> 
> 
>  
> <http://us.adserver.yahoo.com/l?
M=295196.4901138.6052515.3001176/D=groups/S=
> :HM/A=2128215/rand=819205855> 
> 
>  
> 
>   _____  
> 
> Yahoo! Groups Links
> 
> *	To visit your group on the web, go to:
> http://groups.yahoo.com/group/lpc2000/
>   
> *	To unsubscribe from this group, send an email to:
> lpc2000-unsubscribe@yahoogroups.com
> <mailto:lpc2000-unsubscribe@yahoogroups.com?subject=Unsubscribe> 
>   
> *	Your use of Yahoo! Groups is subject to the Yahoo!
> <http://docs.yahoo.com/info/terms/>  Terms of Service.