Lpc2000

Dohery,

Make sure that JP12(On board debug) is also removed. 

I never had to load any config files, auto-detect worked right away. I guess
you can't reset the hardware even when you use the config files, can you?

My version of multiICE server is 2.1.

As for the config files, are you talking about the ones supplied by the ARM
(MultiICE) or something else?

Regards,

m. 

 

  _____  

From: Pauric Doherty [mailto:pauric_doherty@...] 
Sent: Tuesday, May 04, 2004 12:50 PM
To: lpc2000@yahoogroups.com
Subject: RE: [lpc2000] Ashling EVBA7 & ARM Multi-ICE

 

Milos

 

When I try to run the auto configure command, multi-ICE comes up with an
error message "Auto configuration Failed. Check the target power is on. Your
chip may require manual configuration"

 

When I try to load it with the supplied configuration called single.cfg, it
tells me that there is an ARM7TDMI present, but when I run AXD I get a
message telling me that "The processor will not enter debug state when
requested" and I then receive subsequent messages while trying to force a
reset.

 

On the EVAB7 I have 

JP6 (ENABLE SERIAL_ISP) removed

JP11 (ENABLE PRIMARY DEBUG) inserted

JP8 (SECONDARY DEBUG) removed

 

Do I have to manually configure a target for Multi-ICE or should auto
configure work?

 

Thanks

Pauric

 

-----Original Message-----
From: Milos Prokic [mailto:mproki@...]
Sent: 04 May 2004 17:23
To: lpc2000@yahoogroups.com
Subject: RE: [lpc2000] Ashling EVBA7 & ARM Multi-ICE

Hi,

I have setup the MultICE to work with the Ashling. I only had to remove the
jumper for on-board debug, and leave the jumper on primary debug, do not
switch it to the secondary. MultiICE detected the core without any problems.
Once the core was detected I was able to reset and run the AXD.

Does multiICE see anything? Unknown device or something? 

Cheers,

m.

 


  _____  


From: Pauric Doherty [mailto:pauric_doherty@...] 
Sent: Tuesday, May 04, 2004 12:20 PM
To: lpc2000@yahoogroups.com
Subject: [lpc2000] Ashling EVBA7 & ARM Multi-ICE

 

All,

 

I'm currently trying to get the ARM Multi-ICE unit to connect to the EVBA7
board from Ashling with an LCP2194 chip. 

I cannot get the multi-ICE unit to reset the chip. It won't even auto detect
it. I've followed the guide on how to enable the board for an external
debugger but still no luck.

 

Has anyone tried the above situation .... or am I missing something obvious.

 

Thanks in advance

Pauric

 

 






Yahoo! Groups Sponsor



ADVERTISEMENT
 
<http://rd.yahoo.com/SIG=129gtjuh2/M=295196.4901138.6052515.3001176/D=groups
/S=1706554205:HM/EXP=1083775489/A=2128215/R=0/SIG=10se96mf6/*http:/companion
.yahoo.com> click here


 
<http://us.adserver.yahoo.com/l?M=295196.4901138.6052515.3001176/D=groups/S=
:HM/A=2128215/rand=819205855> 

 

  _____  

Yahoo! Groups Links

*	To visit your group on the web, go to:
http://groups.yahoo.com/group/lpc2000/
  
*	To unsubscribe from this group, send an email to:
lpc2000-unsubscribe@yahoogroups.com
<mailto:lpc2000-unsubscribe@yahoogroups.com?subject=Unsubscribe> 
  
*	Your use of Yahoo! Groups is subject to the Yahoo!
<http://docs.yahoo.com/info/terms/>  Terms of Service.