Anybody need knobs?
2002-11-19 by mate_stubb
I need some knobs, and seem to have a choice of paying Newark through the nose or ordering 250 pieces minimum from Dee to get a decent price. I need 50, does
Messages
Browse messages
Page 343 of 690 · 34488 messages matched
Re: [motm] There's noplace like home
2002-11-19 by Neil Bradley
... If only we could all aspire to this standard... ;-) I have a Nord Modular patch called Fartomatic, complete with frequency and watery knobs. If you have
There's noplace like home
2002-11-19 by mate_stubb
I just wanted to note with appreciation the civility and the general relevance of the discussions on this list. Just recently we ve been talking about analog
FW: [motm] Mseq!!
2002-11-19 by Tkacs, Ken
But can it run DOS...? ... From: Paul Schreiber [mailto:synth1@airmail.net] It has 32K of FLASH nonvolatile memory. Over 10 years of storage, no batteries.
Re: [motm] Mseq!!
2002-11-19 by Paul Schreiber
... It has 32K of FLASH nonvolatile memory. Over 10 years of storage, no batteries. Paul S.
Re: [motm] SKB pop-up mixer case back installation
2002-11-19 by Simon
How about some pics of a painted/screened/installed back!?!?! Thanks, Simon Canberra AUSTRALIA
SKB pop-up mixer case back installation
2002-11-19 by J. Larry Hendry
When you install your SKB backs into your SKB pop up rack, you should install the backs without the top or bottoms attached, or at least without the screws
Re: [motm] Mseq!!
2002-11-19 by Craig Critchley
From: Paul Schreiber ... in ... Does this mean it has a nonvolatile memory of some sort, or am I reading too much into this? ...Craig
uSeq photo
2002-11-19 by Paul Schreiber
Here is a crappy photo of the MOTM-600 prototype doing a DAC calibration routine. Some things to note: a) not all the parts are stuffed in the board. b) No,
wtb: motm module
2002-11-19 by Paul Wagorn (Worldbid)
looking for a 490 filter or possibly other MOTM modules that are 1/2 sized.... paul
Re: [motm] Mseq!!
2002-11-18 by media.nai@rcn.com
... Can notes be entered via CV as well?? Can notes be selected via CV?? In other words can it function as a traditional CV sequencer where a control
Re: [motm] Mseq!!
2002-11-18 by Paul Schreiber
Is this bit true? -- Notes can be entered over MIDI I.e. I can take a small sequence from my sequencing software and dump it in the MOTM? Please correct me if
Mseq!!
2002-11-18 by Aaron Day
To quote the article-- The 600 Series modules are for control voltage generation. The MOTM-600 mSequencer ($389 assembled) has 9 patterns of 99 steps each.
Last call for Steve Tilelli
2002-11-18 by J. Larry Hendry
Sorry for public band. Steve Tilelli, I have been unable to reach you by e-mail concerning your Stooge panel order. I am sending this to the list in case you
The Big Announcement?
2002-11-18 by alt-mode
OK, the list has been quiet lately... I went to change my address for my subscription to Keyboard Magazine and found the following release at the top of the
Re: [motm] [OT] drummachine.com
2002-11-17 by elhardt@att.net
... Someone told me that they owed a least one or two of the suppliers money. Does anyone know what is up with Miki Tachibana, Drum Machine Museum and
Re: [motm] [Q] RCO (Ramp Controlled Oscillator)
2002-11-16 by J. Larry Hendry
Ah soon, young grasshopper. LH ... From: Adam Schabtach Ooh, wow, I never thought of that. Gotta start building my MiniWave, now that
Re: [motm] [Q] RCO (Ramp Controlled Oscillator)
2002-11-16 by Adam Schabtach
... Ooh, wow, I never thought of that. Gotta start building my MiniWave, now that the arrival of its Stooge panel is approaching (right?). --Adam
Re: [motm] [Q] RCO (Ramp Controlled Oscillator)
2002-11-16 by mate_stubb
Yes. The ramp controlled part refers to the fact that on a wavetable whose position is controlled by an ADC front end, an input consisting of a positive
Re: [motm] [Q] RCO (Ramp Controlled Oscillator)
2002-11-16 by J. Larry Hendry
Which I think many of use will agree is a really cool thing. :) Thanks Paul S, Grant R, and John B. :) Larry H ... From: John Loffink
RE: [motm] [Q] RCO (Ramp Controlled Oscillator)
2002-11-16 by John Loffink
This sounds exactly like a VCO followed by a Miniwave. John Loffink jloffink@austin.rr.com
[OT] drummachine.com
2002-11-16 by Tentochi
I have not been able to get to drummachine.com for the past 2 weeks or so. Someone told me that they owed a least one or two of the suppliers money. Does
[Q] RCO (Ramp Controlled Oscillator)
2002-11-16 by Tentochi
I saw a reference to RCOs used in the Jomox SunSyn. Is this just marketing hype? The more I read, the more it seems like they are just wavetable playback
SKB backs shipping now
2002-11-14 by J. Larry Hendry
Well, Aaron s made up for slow processing my air-mailing my screws FedEx instead of ground. So, I got screwed today. Which means that SKB backs
FS: Blacet Darkstar PCB+Stooge FacePlate
2002-11-14 by Inform3r
Hey Guys. I ve decided to sell my Blacet Darkstar. Basically what I m selling is the PCB with all the component soldered, and a drilled Stooge Darkstar Panel
Re: [motm] Adding CLK OUT to MOTM-101?
2002-11-14 by Adam Schabtach
Richard-- Thanks a bunch for describing your clock-output mod. I may well end up doing the mod your way, instead of tapping the 555 as per my original idea. I
Re: [motm] MOTM-100 vs. MOTM-101?
2002-11-13 by Adam Schabtach
... I was just thinking yesterday about how a mailing list I subscribe to, which is hosted by www.topica.com, has no advertisements in its email. I don t know
SKB back shipping question
2002-11-13 by J. Larry Hendry
SKB backs are here, ready to ship. I have the boxes and everything EXCEPT the screws that I ordered to hold the tops to the backs. They are standard # 6 x
Help - I cannot find Steve Tilelli
2002-11-13 by J. Larry Hendry
Sorry for the public bandwidth. Steve, I am having no luck contacting you about your Stooge panel order. Have you changed your e-mail address? Does anyone
[OT] Analog Days
2002-11-13 by Tentochi
I know quite a few of you are currently reading Analog Days. Open up the jacket all of the way to find a little surprise which is not visible otherwise. I
Re: [motm] Adding CLK OUT to MOTM-101?
2002-11-13 by groovyshaman@snet.net
Both are valid options. There s room for an Int/Ext switch... :) George ... From: Richard Brewster To: ;
Re: [motm] Adding CLK OUT to MOTM-101?
2002-11-13 by Richard Brewster
... Not necessarily. An internal comparator, U7B, processes the external input, which could be any shape waveform, and turns it into a pulse. My clock out
Re: [motm] DIN ! (clock out from 101)
2002-11-12 by J. Larry Hendry
... From: Any, I plan on keeping my Pro-4, and maybe even putting together a KADI breakout panel (are there any Stooge Kenton panels?? It
Yahoo Snoops again...
2002-11-12 by Alan Wagner
Have you seen this????? I just received this from another group I belong to and thought it was a good idea to alert everyone about it. Yahoo is now using
Power Distribution
2002-11-12 by Tentochi
Distributing power in your system to both MOTM and Modc@n modules? Also allows for pitch, gate, trig and CV distribution from keyboard. Here is the solution:
Re: [motm] DIN ! (clock out from 101)
2002-11-12 by media.nai@rcn.com
... Yes, that makes. A way to do this would be to use the 101 internal clock (or any MOTM pulse) at 24 times the frequency for DIN, they divide it down with
Re: [motm] DIN ! (clock out from 101)
2002-11-12 by Aaron Day
I second this. Having a DIN sync somewhere on a panel would be great for playing with other people that have x0x boxes. I love my little 606 but loathe having
Re: [motm] Adding CLK OUT to MOTM-101?
2002-11-12 by media.nai@rcn.com
... If you are using the external input, wouldn t you already have the clock?? If the internal clock is normalled to the external clock input (which I pressume
MOTM-100 vs. MOTM-101?
2002-11-12 by media.nai@rcn.com
I was also just thinking the same thing!! That space for a jack at the end of the bottom row is like a rotating neon sign that says mod me :) Anyway, I was
DIN (was: motm maximum mounting depth)
2002-11-12 by media.nai@rcn.com
... Huh??
Re: [motm] analogue physical modelling samples
2002-11-12 by elhardt@att.net
... waveshaper: http://home.debitel.net/user/jhaible/jh_ana_phys_mod.html
[motm] Need help IDing module....
2002-11-12 by elhardt@att.net
... http://home.freeuk.net/bandpass/bigsynth1.jpg
Re: [sdiy] Re: [AH] MOTM brass demo
2002-11-12 by ixqy@aol.com
In a message dated 11/11/02 8:52:19 PM Central Standard Time, ... I ll second that! :)
Re: [motm] Adding CLK OUT to MOTM-101?
2002-11-12 by Richard Brewster
The available space for another jack was too tempting, so I planned out this modification before initial assembly of my MOTM-101. You have a couple of options
RE: [motm] [OT] Other old modulars....
2002-11-12 by John Loffink
There s a good Aries site here: http://www.fleebite.to/Aries/AriesHome.html In the future they ll have better scans of the 1977 catalog than the link below.
[OT] Other old modulars....
2002-11-12 by Tentochi
I totally forgot what I was orginally going to send. Oh well. A few of you might enjoy these if you haven t seen them before.... Excellent PPG 300 pics:
Re: [motm] Renaissance Brass MP3
2002-11-11 by Tentochi
... That is Jan Pieterszoon Sweelinck (1562 - 1621). Sweelinck was a Dutch organist, teacher, and composer: he is widely considered to be the greatest of Dutch
Re: [motm] Mrs Hendry comes through
2002-11-11 by ixqy@aol.com
Hi Larry, Please send our gracious thanks to Mrs Hendry for us. It is greatly appreciated. Andrew In a message dated 11/10/02 6:05:01 PM Central Standard Time,
Re: [motm] OT: Yamaha Poly-VL
2002-11-11 by Simon
... Yes, this is a hardware expander board for synths as well as the SW1000XG sound card. Kenton makes a rack box to hold four of these cards, it can be used
Re: [motm] OT: Yamaha Poly-VL
2002-11-11 by Simon
... No...if you can translate UK english into US english, there is a 30 day demo on the UK Yamaha site, as Sondius XG...