Re: Polysix ARP Sync
2012-03-20 by nicknak110756
Hi Guys Thanks for all your replies, very much appreciated. I have it up and running now so all good. I ve only just bought the 808 and had nt realised i
Messages
Browse messages
Page 53 of 114 · 5658 messages matched
Re: Polysix ARP Sync
2012-03-19 by feline1973
Duh - yes, sorry, I forget when reading the original post that there was a real TR808 involved. Simply connect a trigger out from the 808 to the V-trig
Re: Polysix ARP Sync
2012-03-19 by bigpeeet@rocketmail.com
David, Not exactly sure this is how the setup is described. I believe the Phil Rees MDS is handling midi to din sync conversion to run the 808 in time with
Re: Polysix ARP Sync
2012-03-18 by feline1973
This is unlikely to work... DIN Sync sends a 24-pulses per quarter note (crotchet), they re 5V TTL... whereas the Polysix arpeggiator simply wants a pulse
Re: Polysix ARP Sync
2012-03-18 by bigpeeet@rocketmail.com
Hi there, I ve used a similar setup with 909 to trig chord through arp trig in, so should work okay. Not sure if this helps, but for each note you ll need a
Polysix ARP Sync
2012-03-17 by nicknak110756
Hi Folks. Im trying to hook my newly acquired Polysix up to my 808 via din sync. Im using a Philip Rees MDS unit to sync the 808 to Logic and an 808 trigger
Keyboard Problem (key assigner)
2012-03-12 by del_poolp@hotmail.com
Hi, I have a P6 (old production) with KLM367A clone. P6 Boot correctly, but the keyboard do not work. The keyboard hardware work with another P6 (new
RE: [PolySix] Battery leak problem.
2012-02-29 by backshall1
Yes, the TC5514 could be faulty, but it would be best to check everything else first. R17 can definitely cause problems on the data bus. It is eight 10k
Re: [PolySix] Battery leak problem.
2012-02-29 by Darijo Berkes
I have measured all th traces from CN10 to all IC that has a connection between D0 to D7 and all is fine. Could it be that the IC 32 is fault ( no battery acid
RE: [PolySix] Battery leak problem.
2012-02-29 by backshall1
Oops, I meant KLM-367 CN10 not KLM-267. _____ From: PolySix@yahoogroups.com [mailto:PolySix@yahoogroups.com] On Behalf Of backshall1 Sent: Wednesday, February
RE: [PolySix] Battery leak problem.
2012-02-29 by backshall1
The patch RAM memory chip is IC 32 TC5514 APL-3 on the KLM367 board. It is very close to the battery. The 8089 on the KLM-366 is the CPU/ROM for the key
Re: [PolySix] Battery leak problem.
2012-02-28 by Takio Hosoya
Hi, everyone, I m one of the newbies from Japan. I answer this question. Darijo, IC 6 is that you want to find. You can find it under a keyboard assembley on
Re: [PolySix] Battery leak problem.
2012-02-28 by Darijo Berkes
What IC is the memory? Sent from my iPad
RE: [PolySix] Battery leak problem.
2012-02-28 by Bruno BzH
Hi, you have probably your memory ic which is out of order, follow the traces and try to test it. Regards Bruno To: PolySix@yahoogroups.com From:
Battery leak problem.
2012-02-28 by Darijo Berkes
Hi, I have tried to fix my Polysix that had a battery leak. Before i started to repar the problem was that no button was working (for memory and tape) and
RE: [PolySix] help to find out where 2 cables are going?
2012-02-27 by backshall1
The blue wire to D1 is +5v to power the MG light, the LED that blinks to show MG speed, and should be connected to the power supply board KLM-376 where it says
help to find out where 2 cables are going?
2012-02-26 by Darijo Berkes
Hi everyone! I had a problem with my Polysix so I opend it and saw two cables that was just solderd to one side, the other side is just hanging. I was
Re: Calibrating PolySix VCF section on KLM-366 question
2012-02-11 by sigma.draconis
When I want to make a photo off the waveform, I found out that some parts aren t working correct anymore. So indeed the clean waveforms are not as they used
Re: [PolySix] Calibrating PolySix VCF section on KLM-366 question
2012-02-10 by Johannes Hausensteiner
1. Is it the same wioth all six voices that you cannot adjust for the requested value? 2. Can you post a picture of the oscilloscope screen? 3. I would not
Re: Calibrating PolySix VCF section on KLM-366 question
2012-02-09 by sigma.draconis
... Yes, that makes sence to me to. I just fixed a Juno-106 (my other hobby project) with broken voice and the calibrating of the filters was just as you
[PolySix] Re: Calibrating PolySix VCF section on KLM-366 question
2012-02-09 by Malte Rogacki
... Pretty much like a sine wave, regardless of the frequency. ... So it looks more like a sawtooth? This definitely should not happen. Does the Polysix work
Re: Calibrating PolySix VCF section on KLM-366 question
2012-02-09 by sigma.draconis
Thanks for replay. ... Indeed, the KBD TRACK is pointed at zero, and everything else is set to standard . Except WAVE-FORM at PW and PW/PWM to 10. And
Re: [PolySix] External filter control details
2012-02-09 by Malte Rogacki
Most other Korg equipment from roughly this timeframe expects control voltages between -5V and +5V for filter control as well. Negative voltages probably lower
Re: [PolySix] Calibrating PolySix VCF section on KLM-366 question
2012-02-09 by Malte Rogacki
... Hold it right there. It s normal that the voices differ (especially before calibration). However if the keys also affect the frequency you may have not set
External filter control details
2012-02-09 by Ian MacMillan
Could someone provide an explanation of how the external filter control input on the back of the Polysix functions that is more specific than the manual? I m
Calibrating PolySix VCF section on KLM-366 question
2012-02-08 by sigma.draconis
Hi, Im having problems to calibrate the filter section on the KLM366 board. I followed the procedure from the servicemanual, and everything went well until:
Re: [PolySix] Re: Noise in my soup
2012-02-02 by Mike
You need to know where the noise is coming from. Do not work on P6 while powered on! Remove IC 10 on the voice board. This will take out all voices. Noise
Re: [PolySix] Re: Noise in my soup
2012-02-01 by Dennis Matana
Sounds to me like an opamp isn´t functioning correctly. They tend to create a lot of noise if going bad. http://soundcloud.com/wifi
Re: Noise in my soup
2012-02-01 by bigpeeet@rocketmail.com
It s a high end hiss, like you d expect from a channel strip gain being too high on a mixer. Seems like a bad signal/noise ratio in the output, if you know
Re: [PolySix] Noise in my soup
2012-01-31 by Mike
What type of noise? Hum, hiss or a random popcorn/crackle? Sent from my Apple ][e ... [Non-text portions of this message have been removed]
Noise in my soup
2012-01-31 by bigpeeet@rocketmail.com
Does anyone else have a problem with noisy outputs? I m aware of two remedies: the insulation mod for the fx board described by Johannes, or re-capping. I have
Re: [PolySix] Waveform Switch replacement source?
2012-01-26 by klosmon
... Vintage Planet at http://www.vintageplanet.nl/ lists these (and many other parts for many synths). [Non-text portions of this message have been removed]
Waveform Switch replacement source?
2012-01-26 by noisepenguin
Hello, I need to replace this on mine since the post on it broke. thanks.
Re: Does Andrew still do the board exchange service for tthe KLM-367A?
2012-01-24 by noisepenguin
Hey Andy, I wasn t sure if my email went thru or not thru your site, I thought I had entered the security code wrong, so I may have sent it twice. Looking
Re: [PolySix] Does Andrew still do the board exchange service for tthe KLM-367A?
2012-01-24 by Andrew Jury
Hi Brent, I saw your mail come in recently about this. I haven t forgotten about you. I will write privately with details when I am done in the workshop for
Re: [PolySix] Does Andrew still do the board exchange service for tthe KLM-367A?
2012-01-24 by Jed Jorgensen
He does. http://synthprof.com/clone_367.html ... jed ... [Non-text portions of this message have been removed]
Does Andrew still do the board exchange service for tthe KLM-367A?
2012-01-24 by noisepenguin
Hello everyone, Does Andrew still do this? I have a new clone pcb waiting to be populated and a dead Polysix that really needs to be resurrected. Thanks,
Re: [PolySix] Clone Boards? Any left?
2012-01-20 by Jed Jorgensen
I ve got lots! You can buy them here: http://sites.google.com/site/jedjorgensen/ Cheers, Jed ... [Non-text portions of this message have been removed]
Clone Boards? Any left?
2012-01-20 by noisepenguin
Hello, I missed the boat multiple times but I still need a clone board, are there still any available?
Re: Polysix Midi Project
2012-01-16 by bigpeeet@rocketmail.com
Thanks for the encouragement! Andy Jury has just recently shipped mine completed ready for installation. I figured that it would be better to get it done by a
Re: [PolySix] Question for those that either have parts or work with the clone board.
2011-12-20 by Jed Jorgensen
A new thermistor should work. I had one in mine and the performance was fine. I bought a new CPU here: http://www.analogsynthservice.com/poly6.html I used
Question for those that either have parts or work with the clone board.
2011-12-20 by Daniel A
Someone purchased one of my clone boards populated with everything except the CPU, Molex conectors and TH1. He is now stating his KLM367 was stolen and does
Re: [PolySix] big problem with my polysix
2011-12-15 by Malte Rogacki
... Could be damage from battery leakage. As I witnessed recently those batteries may still supply sufficient output to retain the memory but at the same time
Re: [PolySix] simple question about the battery of the P6
2011-12-15 by Malte Rogacki
Just a quick reminder: The 5514AP/APL has a range of 2 to 5.5 volts for the data retention supply voltage. So as long as the voltage is above 2 volts no memory
Re: [PolySix] simple question about the battery of the P6
2011-12-14 by Ben Stuyts
... It would start to loose its memory. Ben
simple question about the battery of the P6
2011-12-14 by Ainardi
hello i have just a little question about the battery on the schematics and the service manual it is said that the output of the battery must be between 3.0
simple question about the battery of the P6
2011-12-14 by Ainardi
hello i have just a little question about the battery on the schematics and the service manual it is said that the output of the battery must be between 3.0
big problem with my polysix
2011-12-14 by Ainardi
hello all i have a new big problem with my polysix when i turn it on, there are a lot of noise on the output, no equal sound on the same key , and the led of
Correction to my previous post.
2011-12-11 by Kenneth
I wrote in my previous post: Whenever I turn it off its sound is bad. Kind of sounds like a fast LFO is modulating the pitch/volume. What I meant to write
Problems with Polysix - may be battery related.
2011-12-11 by Kenneth
Dear group. I have a nice Polysix with a quiet annoying problem. Whenever I turn it off its sound is bad. Kind of sounds like a fast LFO is modulating the