Mailist to discuss all issues regarding the Digitech GSP-2101 Guitar FX Processor

I bought this midi controller to use with my 2101.
I can get it to change my patches but I cannot get the expression 
pedals to work. They will not calibrate. I have searched the 
archives but have found nothing. Can anybody help me with this 
problem?

James,

I also replaced fairly recently my ART X-15 controller for the FCB. 
It's working nicely.

If you want to calibrate the exp pedals (I didn't have to), read the 
FCB manual for instructions.

But on the other hand, check the following:
ON THE FCB:
- Pick the patch number you want to use, probably matching that on 
the GSP.
- Enter edit mode by pressing and keeping for 3 seconds the 'down' 
pedal. The green edit led should go on.
- Press the'up' pedal. You should see those controllers currently 
programmed lighting up, represented by each one of the pedals. Some 
might be off. Most likely, 8 and 9 (indicating the exp pedals) should 
be on.
- Press either 8 or 9, depending on which one you want to use. 
Press 'up' pedal (enter)
- The two-digit red display shows the controller number currently 
selected. Change it if you want (use the exp pedal to toggle the 
value), if not, just leave it as is, doesn't matter much. 
- Press 'up' and you get to the LOW value. Make sure it's 0 (exp 
pedal again).
- Press 'up', you get to the HIGH value. Make sure it is 127.
- Press 'up' again twice, set-up is complete. Now keep 'down' pressed 
for three seconds to get out to normal operation.

ON THE GSP:
- Select the patch you want.
- Enter the MIDI edit mode (MIDI key on the front panel)
- Navigate to LINK (hit 'next' once). Press '1' to link the parameter 
selected.
- Use the selector to toggle the controller as to show CCxx, xx being 
the same number that you had on the FCB.
- SAVE!!!

It should work now (this was all by memory, hope I didn't forget any 
step).

Gus.



--- In gsp-2101@yahoogroups.com, "jamesleehumes" <jamesleehumes@y...> 
wrote:

> 
> I bought this midi controller to use with my 2101.
> I can get it to change my patches but I cannot get the expression 
> pedals to work. They will not calibrate. I have searched the 
> archives but have found nothing. Can anybody help me with this 
> problem?

you must configure the CC (continuos control) number in the FCB1010 and after 
configure the same number into  GSP-2101.
if i do not forget the menu is <utility> <foot control>



regard.


Em Sábado 22 Janeiro 2005 19:40, jamesleehumes escreveu:
> I bought this midi controller to use with my 2101.
> I can get it to change my patches but I cannot get the expression
> pedals to work. They will not calibrate. I have searched the
> archives but have found nothing. Can anybody help me with this
> problem?
>
>
>
>
>
>
>
> Yahoo! Groups Links
>
>
>

-- 
Henrique Leandro
Gerencia de Redes e Telecom.
Varig S.A
55-11-5091-2318
55-11-8182-6415

Thanks Gus and Henrique!

My mistake was at the GSP end. I have got one of the expression 
pedals to work. I am trying to get one set up as a volume control and 
the other for delay level. With just a little more time I think I can 
achieve this.

Thanks again for your help!

James

--- In gsp-2101@yahoogroups.com, Henrique Leandro 
<henrique.leandro@v...> wrote:
> you must configure the CC (continuos control) number in the FCB1010 
and after 

> configure the same number into  GSP-2101.
> if i do not forget the menu is <utility> <foot control>
> 
> 
> 
> regard.
> 
> 
> Em Sábado 22 Janeiro 2005 19:40, jamesleehumes escreveu:
> > I bought this midi controller to use with my 2101.
> > I can get it to change my patches but I cannot get the expression
> > pedals to work. They will not calibrate. I have searched the
> > archives but have found nothing. Can anybody help me with this
> > problem?
> >
> >
> >
> >
> >
> >
> >
> > Yahoo! Groups Links
> >
> >
> >
> 
> -- 
> Henrique Leandro
> Gerencia de Redes e Telecom.
> Varig S.A
> 55-11-5091-2318
> 55-11-8182-6415

Hello james and everybody,

maybe if you configure the external CC to trigger from GSP  into CC number of 
second expression from FCB 1010  and attach volume or others

what you think ?


regards.



Em Segunda 24 Janeiro 2005 17:57, jamesleehumes escreveu:
> Thanks Gus and Henrique!
>
> My mistake was at the GSP end. I have got one of the expression
> pedals to work. I am trying to get one set up as a volume control and
> the other for delay level. With just a little more time I think I can
> achieve this.
>
> Thanks again for your help!
>
> James
>
> --- In gsp-2101@yahoogroups.com, Henrique Leandro
>
> <henrique.leandro@v...> wrote:
> > you must configure the CC (continuos control) number in the FCB1010
>
> and after
>
> > configure the same number into  GSP-2101.
> > if i do not forget the menu is <utility> <foot control>
> >
> >
> >
> > regard.
> >
> > Em Sábado 22 Janeiro 2005 19:40, jamesleehumes escreveu:
> > > I bought this midi controller to use with my 2101.
> > > I can get it to change my patches but I cannot get the expression
> > > pedals to work. They will not calibrate. I have searched the
> > > archives but have found nothing. Can anybody help me with this
> > > problem?
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > > Yahoo! Groups Links
> >
> > --
> > Henrique Leandro
> > Gerencia de Redes e Telecom.
> > Varig S.A
> > 55-11-5091-2318
> > 55-11-8182-6415
>
>
>
> Yahoo! Groups Links
>
>
>

-- 
Henrique Leandro
Gerencia de Redes e Telecom.
Varig S.A
55-11-5091-2318
55-11-8182-6415

Hi All,

I got both expression pedal working last night.
I assinged the master volume to CC#07 and the delay level to CC#10 on 
both the FCB1010 and the 2101. It works like a charm! I use less than 
10 patches live so I will finish configuring the remaining patches 
and I am good to go.

Thanks again for your help!

--- In gsp-2101@yahoogroups.com, Henrique Leandro 
<henrique.leandro@v...> wrote:
> Hello james and everybody,
> 
> maybe if you configure the external CC to trigger from GSP  into CC 
number of 
> second expression from FCB 1010  and attach volume or others
> 
> what you think ?
> 
> 
> regards.
> 
> 
> 
> Em Segunda 24 Janeiro 2005 17:57, jamesleehumes escreveu:
> > Thanks Gus and Henrique!
> >
> > My mistake was at the GSP end. I have got one of the expression
> > pedals to work. I am trying to get one set up as a volume control 
and
> > the other for delay level. With just a little more time I think I 
can
> > achieve this.
> >
> > Thanks again for your help!
> >
> > James
> >
> > --- In gsp-2101@yahoogroups.com, Henrique Leandro
> >
> > <henrique.leandro@v...> wrote:
> > > you must configure the CC (continuos control) number in the 
FCB1010
> >
> > and after
> >
> > > configure the same number into  GSP-2101.
> > > if i do not forget the menu is <utility> <foot control>
> > >
> > >
> > >
> > > regard.
> > >
> > > Em Sábado 22 Janeiro 2005 19:40, jamesleehumes escreveu:
> > > > I bought this midi controller to use with my 2101.
> > > > I can get it to change my patches but I cannot get the 
expression

> > > > pedals to work. They will not calibrate. I have searched the
> > > > archives but have found nothing. Can anybody help me with this
> > > > problem?
> > > >
> > > >
> > > >
> > > >
> > > >
> > > >
> > > >
> > > > Yahoo! Groups Links
> > >
> > > --
> > > Henrique Leandro
> > > Gerencia de Redes e Telecom.
> > > Varig S.A
> > > 55-11-5091-2318
> > > 55-11-8182-6415
> >
> >
> >
> > Yahoo! Groups Links
> >
> >
> >
> 
> -- 
> Henrique Leandro
> Gerencia de Redes e Telecom.
> Varig S.A
> 55-11-5091-2318
> 55-11-8182-6415