Yahoo Groups archive
Thread
2005-02-22 by kenbnny
Hello Guys, I'm using OCD commander software of Macraigor Systems for connecting to the LPC device using "WIGGLER" Interface. Does anybody know why always I get this message reported. "Error Response from INITIALIZE: 0x03 initialize_target : cable disconnected (10 : 03)" Ken
2005-02-22 by Bruce Paterson
kenbnny wrote:
>
> Hello Guys,
>
> I'm using OCD commander software of Macraigor Systems for connecting
> to the LPC device using "WIGGLER" Interface.
>
> Does anybody know why always I get this message reported.
> "Error Response from INITIALIZE: 0x03 initialize_target : cable
> disconnected (10 : 03)"
Are you using a Macraigor Wiggler or a home built one ?
Recently Macraigor added code to their later ocd commander on ocdremote
software to sense a looped back pin to see if a 'real' wiggler or not.
Suggestions:
* Try an older version of ocd commander (I don't have, but sure someone
here will. I only have an older version of ocdremote).
* Look back through this list history to see which pins need to be
looped back on a home grown wiggler to make it look like a macraigor.
* Check your parallel port is in EPP mode (CMOS setup).
--
Cheers,
Bruce
-------------------------------------------------------------------
This email and any files transmitted with it are confidential and
intended solely for the use of the individual or entity to whom
they are addressed. If you have received this email in error please
notify the system manager.
/\\\/\\\/\\\ / / Bruce Paterson
/ \\\ \\\ \\\ / / Senior Design Engineer
/ /\\\/\\\/\\\/ / 8 Anzed Court, Mulgrave, Vic, 3170
/ / \\\ \\\ \\\ / PO Box 4112, Mulgrave, Vic, 3170, Australia
/ / \\\/\\\ \\\/ Ph: +61 3 8561 4232 Fax: +61 3 9560 9055
Tele-IP Ltd. Email: bruce@... Icq: #32015991
WWW: http://www.tele-ip.com VK3TJN
-------------------------------------------------------------------2005-02-22 by kenbnny
Bruce, I'm using home made wiggler interface as per Schematic given in JTAG.ZIP in group files. Where can I get information regarding which loopback pins connection. Also looking for older version of 2.06version OCD commander software. Thanks, Ken --- In lpc2000@yahoogroups.com, Bruce Paterson <bruce@t...> wrote: > kenbnny wrote: > > > > > Hello Guys, > > > > I'm using OCD commander software of Macraigor Systems for connecting > > to the LPC device using "WIGGLER" Interface. > > > > Does anybody know why always I get this message reported. > > "Error Response from INITIALIZE: 0x03 initialize_target : cable > > disconnected (10 : 03)" > > Are you using a Macraigor Wiggler or a home built one ? > Recently Macraigor added code to their later ocd commander on ocdremote > software to sense a looped back pin to see if a 'real' wiggler or not. > > Suggestions: > * Try an older version of ocd commander (I don't have, but sure someone > here will. I only have an older version of ocdremote). > * Look back through this list history to see which pins need to be > looped back on a home grown wiggler to make it look like a macraigor.
> * Check your parallel port is in EPP mode (CMOS setup). > > > -- > Cheers, > Bruce > ------------------------------------------------------------------- > This email and any files transmitted with it are confidential and > intended solely for the use of the individual or entity to whom > they are addressed. If you have received this email in error please > notify the system manager. > > /\\\/\\\/\\\ / / Bruce Paterson > / \\\ \\\ \\\ / / Senior Design Engineer > / /\\\/\\\/\\\/ / 8 Anzed Court, Mulgrave, Vic, 3170 > / / \\\ \\\ \\\ / PO Box 4112, Mulgrave, Vic, 3170, Australia > / / \\\/\\\ \\\/ Ph: +61 3 8561 4232 Fax: +61 3 9560 9055 > Tele-IP Ltd. Email: bruce@t... Icq: #32015991 > WWW: http://www.tele-ip.com VK3TJN > -------------------------------------------------------------------
2005-02-22 by Gawie de Vos
As far as I know, you should connect pin 8 and 15 on the DB25. ________________________________
From: kenbnny [mailto:kenbnny@...] Sent: 22 February 2005 08:15 AM To: lpc2000@yahoogroups.com Subject: [lpc2000] Re: OCD commander Bruce, I'm using home made wiggler interface as per Schematic given in JTAG.ZIP in group files. Where can I get information regarding which loopback pins connection. Also looking for older version of 2.06version OCD commander software. Thanks, Ken --- In lpc2000@yahoogroups.com, Bruce Paterson <bruce@t...> wrote: > kenbnny wrote: > > > > > Hello Guys, > > > > I'm using OCD commander software of Macraigor Systems for connecting > > to the LPC device using "WIGGLER" Interface. > > > > Does anybody know why always I get this message reported. > > "Error Response from INITIALIZE: 0x03 initialize_target : cable > > disconnected (10 : 03)" > > Are you using a Macraigor Wiggler or a home built one ? > Recently Macraigor added code to their later ocd commander on ocdremote > software to sense a looped back pin to see if a 'real' wiggler or not. > > Suggestions: > * Try an older version of ocd commander (I don't have, but sure someone > here will. I only have an older version of ocdremote). > * Look back through this list history to see which pins need to be > looped back on a home grown wiggler to make it look like a macraigor. > * Check your parallel port is in EPP mode (CMOS setup). > > > -- > Cheers, > Bruce > ------------------------------------------------------------------- > This email and any files transmitted with it are confidential and > intended solely for the use of the individual or entity to whom > they are addressed. If you have received this email in error please > notify the system manager. > > /\\\/\\\/\\\ / / Bruce Paterson > / \\\ \\\ \\\ / / Senior Design Engineer > / /\\\/\\\/\\\/ / 8 Anzed Court, Mulgrave, Vic, 3170 > / / \\\ \\\ \\\ / PO Box 4112, Mulgrave, Vic, 3170, Australia > / / \\\/\\\ \\\/ Ph: +61 3 8561 4232 Fax: +61 3 9560 9055 > Tele-IP Ltd. Email: bruce@t... Icq: #32015991 > WWW: http://www.tele-ip.com VK3TJN > ------------------------------------------------------------------- ________________________________ Yahoo! Groups Links * To visit your group on the web, go to: http://groups.yahoo.com/group/lpc2000/ * To unsubscribe from this group, send an email to: lpc2000-unsubscribe@yahoogroups.com <mailto:lpc2000-unsubscribe@yahoogroups.com?subject=Unsubscribe> * Your use of Yahoo! Groups is subject to the Yahoo! Terms of Service <http://docs.yahoo.com/info/terms/> . [Non-text portions of this message have been removed]
2005-02-22 by Gawie de Vos
Hi Ken Look at http://sysadminforum.com/showthread.php?s=8b64fe3da5c435f497ad868f34952f 99&t=238739&page=2&pp=10 for more info regarding the loopback required on the Wiggler. Cheers, Gawie [Non-text portions of this message have been removed]
2005-02-22 by kenbnny
Guys, A little joy with pin 8 and pin 15 connected on DB25 with latest OCD software at speed 8, I'm able to connect to target, but I'm not able to load file. Any ideas how can I fix this up. Error I get on window. D:\Keil\ARM\Examples\Blinky\Obj\Blinky.elf: downloaded 272 bytes in 0 minutes, 27.28 seconds Error during download PC set to starting address 0x00000000 Regards, Raj --- In lpc2000@yahoogroups.com, "Gawie de Vos" <gawie.devos@c...> wrote: > Hi Ken > > > > Look at > http://sysadminforum.com/showthread.php? s=8b64fe3da5c435f497ad868f34952f > 99&t=238739&page=2&pp=10 for more info regarding the loopback required
> on the Wiggler. > > > > Cheers, > > Gawie > > > > [Non-text portions of this message have been removed]
2005-02-22 by Leon Heller
----- Original Message -----
From: "kenbnny" <kenbnny@...> To: <lpc2000@yahoogroups.com> Sent: Tuesday, February 22, 2005 4:02 AM Subject: [lpc2000] OCD commander > > > Hello Guys, > > I'm using OCD commander software of Macraigor Systems for connecting > to the LPC device using "WIGGLER" Interface. > > Does anybody know why always I get this message reported. > "Error Response from INITIALIZE: 0x03 initialize_target : cable > disconnected (10 : 03)" Could be lots of things. Have a look at my web site - I've got a simple LPC210x system there with the Wiggler connections that work for me. You need EPP mode for the printer port. Leon -- Leon Heller, G1HSM http://www.geocities.com/leon_heller -- No virus found in this outgoing message. Checked by AVG Anti-Virus. Version: 7.0.300 / Virus Database: 266.1.0 - Release Date: 18/02/2005
2005-02-22 by Anton Erasmus
On 22 Feb 2005 at 7:26, kenbnny wrote: > > > Guys, > > A little joy with pin 8 and pin 15 connected on DB25 with latest OCD > software at speed 8, I'm able to connect to target, but I'm not able > to load file. Any ideas how can I fix this up. > > Error I get on window. > > D:\Keil\ARM\Examples\Blinky\Obj\Blinky.elf: downloaded 272 bytes in 0 > minutes, 27.28 seconds > > Error during download > > PC set to starting address 0x00000000 > Do you have RAM at the address you are trying to download ? AFAIK the OCD JTAG download, only downloads to RAM. If you want to program FLASH via JTAG, you need to download a small app that runs in RAM, and uses the normal built-in routines to write to FLASH. Regards Anton Erasmus > > --- In lpc2000@yahoogroups.com, "Gawie de Vos" <gawie.devos@c...> > wrote: > Hi Ken > > > > Look at > > http://sysadminforum.com/showthread.php? > s=8b64fe3da5c435f497ad868f34952f > 99&t=238739&page=2&pp=10 for more > info regarding the loopback required > on the Wiggler. > > > > > Cheers, > > Gawie > > > > [Non-text portions of this message have been > removed] > > > > > > > Yahoo! Groups Links > > > > > > > -- A J Erasmus