OBERHEIM SYNTH

From: Paul J. White
Subject: Re: [oberheim] obxa factory presets--do I have dead memory patches?
To: oberheim@yahoogroups.com
Date: Saturday, May 30, 2009, 5:57 PM

At 04:39 PM 5/30/09, you wrote:
>Hello: at the cost of a small fortune, I've just successfully
>restored an OBX-A that was left for scrap. My repair (surprisingly)
>had a backup tape of the presets from another obxa that had come
>through his shop. Listening to the presents that loaded in and
>comparing them to the preset chart in the owner's manual shows that
>most of these are the factory presets (there may be a couple of the
>other owern's patches thrown in). Here's my issue. for patch A3 and
>the last two groups (CD and ACD) if I push the patch combinations,
>different lights light up, indicating to me that the patch is
>actually loaded and the synth has turned on the various parameters
>that make up that particular patch, e.g, saw versus other waves,
>unison or not, s/h or not, etc.--but NO SOUND comes out. What does
>this indicate? There is something wrong with the memory patch of the
>synth for those patches? Something else? Thanks in advance for any
>suggestions.

I can think of a couple of possibilities:
1. Bad patch tape. Try programming patch A3 manually (see patch
sheet here http://www.electron gate.com/ obfiles/OB- Xa_patch_ A3.jpg)
and see if it works OK.
2. Bad or missing RAM chip. Try storing a working patch in the CD
and ACD banks and see if they stick.

Good luck.

-- Paul White

From: Paul J. White
Subject: Re: [oberheim] obxa factory presets--do I have dead memory patches?
To: oberheim@yahoogroups.com
Date: Saturday, May 30, 2009, 5:57 PM

At 04:39 PM 5/30/09, you wrote:
>Hello: at the cost of a small fortune, I've just successfully
>restored an OBX-A that was left for scrap. My repair (surprisingly)
>had a backup tape of the presets from another obxa that had come
>through his shop. Listening to the presents that loaded in and
>comparing them to the preset chart in the owner's manual shows that
>most of these are the factory presets (there may be a couple of the
>other owern's patches thrown in). Here's my issue. for patch A3 and
>the last two groups (CD and ACD) if I push the patch combinations,
>different lights light up, indicating to me that the patch is
>actually loaded and the synth has turned on the various parameters
>that make up that particular patch, e.g, saw versus other waves,
>unison or not, s/h or not, etc.--but NO SOUND comes out. What does
>this indicate? There is something wrong with the memory patch of the
>synth for those patches? Something else? Thanks in advance for any
>suggestions.

I can think of a couple of possibilities:
1. Bad patch tape. Try programming patch A3 manually (see patch
sheet here http://www.electron gate.com/ obfiles/OB- Xa_patch_ A3.jpg)
and see if it works OK.
2. Bad or missing RAM chip. Try storing a working patch in the CD
and ACD banks and see if they stick.

Good luck.

-- Paul White

>i appreciate your help. you know that's a lot of work for you to 
>scan all that. don't you want me to just buy a copy of the patch 
>book from you, at least to compensate you for your time?
>
>Jonathan G. Chance, Esq.
>JC Law Offices
>1840 Gateway Dr.
>Suite 200
>San Mateo, CA 94404
>650-378-1383 (office)
>650-921-4696 (cell)
>650-429-2048 (fax)
><mailto:lawjcrg@...>lawjcrg@...
>www.jchancelaw.com
>
>
>--- On Sat, 5/30/09, Paul J. White <pjwhite@...> wrote:
>
>From: Paul J. White <pjwhite@...>
>Subject: Re: [oberheim] obxa factory presets--do I have dead memory patches?
>To: oberheim@yahoogroups.com
>Date: Saturday, May 30, 2009, 5:57 PM
>
>At 04:39 PM 5/30/09, you wrote:
> >Hello: at the cost of a small fortune, I've just successfully
> >restored an OBX-A that was left for scrap. My repair (surprisingly)
> >had a backup tape of the presets from another obxa that had come
> >through his shop. Listening to the presents that loaded in and
> >comparing them to the preset chart in the owner's manual shows that
> >most of these are the factory presets (there may be a couple of the
> >other owern's patches thrown in). Here's my issue. for patch A3 and
> >the last two groups (CD and ACD) if I push the patch combinations,
> >different lights light up, indicating to me that the patch is
> >actually loaded and the synth has turned on the various parameters
> >that make up that particular patch, e.g, saw versus other waves,
> >unison or not, s/h or not, etc.--but NO SOUND comes out. What does
> >this indicate? There is something wrong with the memory patch of the
> >synth for those patches? Something else? Thanks in advance for any
> >suggestions.
>
>I can think of a couple of possibilities:
>1. Bad patch tape. Try programming patch A3 manually (see patch
>sheet here 
><http://www.electrongate.com/obfiles/OB-Xa_patch_A3.jpg>http://www.electron 
>gate.com/ obfiles/OB- Xa_patch_ A3.jpg)
>and see if it works OK.
>2. Bad or missing RAM chip. Try storing a working patch in the CD
>and ACD banks and see if they stick.
>
>Good luck.
>
>-- Paul White
>
>

From: Paul J. White
Subject: [oberheim] OB-Xa Programmed Patches
To: oberheim@yahoogroups.com
Date: Sunday, May 31, 2009, 10:41 AM

As promised, I have scanned and uploaded the Oberheim OB-Xa "Programmed Patches" book to my website at this address:

http://www.electron gate.com/ obfiles/OB- Xa/patchbook. html

Enjoy, and let me know if you find any broken links or mistakes.

Thanks,
Paul White

At 10:49 PM 5/30/09, you wrote:

i appreciate your help. you know that's a lot of work for you to scan all that. don't you want me to just buy a copy of the patch book from you, at least to compensate you for your time?

Jonathan G. Chance, Esq.
JC Law Offices
1840 Gateway Dr.
Suite 200
San Mateo, CA 94404
650-378-1383 (office)
650-921-4696 (cell)
650-429-2048 (fax)
lawjcrg@yahoo. com
www.jchancelaw. com


--- On Sat, 5/30/09, Paul J. White wrote:

From: Paul J. White
Subject: Re: [oberheim] obxa factory presets--do I have dead memory patches?
To: oberheim@yahoogroup s.com
Date: Saturday, May 30, 2009, 5:57 PM

At 04:39 PM 5/30/09, you wrote:
>Hello: at the cost of a small fortune, I've just successfully
>restored an OBX-A that was left for scrap. My repair (surprisingly)
>had a backup tape of the presets from another obxa that had come
>through his shop. Listening to the presents that loaded in and
>comparing them to the preset chart in the owner's manual shows that
>most of these are the factory presets (there may be a couple of the
>other owern's patches thrown in). Here's my issue. for patch A3 and
>the last two groups (CD and ACD) if I push the patch combinations,
>different lights light up, indicating to me that the patch is
>actually loaded and the synth has turned on the various parameters
>that make up that particular patch, e.g, saw versus other waves,
>unison or not, s/h or not, etc.--but NO SOUND comes out. What does
>this indicate? There is something wrong with the memory patch of the
>synth for those patches? Something else? Thanks in advance for any
>suggestions.

I can think of a couple of possibilities:
1. Bad patch tape. Try programming patch A3 manually (see patch
sheet here http://www.electron gate.com/ obfiles/OB- Xa_patch_ A3.jpg)
and see if it works OK.
2. Bad or missing RAM chip. Try storing a working patch in the CD
and ACD banks and see if they stick.

Good luck.

-- Paul White

From: Paul J. White
Subject: [oberheim] OB-Xa Programmed Patches
To: oberheim@yahoogroups.com
Date: Sunday, May 31, 2009, 12:41 PM

As promised, I have scanned and uploaded the Oberheim OB-Xa "Programmed Patches" book to my website at this address:

http://www.electron gate.com/ obfiles/OB- Xa/patchbook. html

Enjoy, and let me know if you find any broken links or mistakes.

Thanks,
Paul White

At 10:49 PM 5/30/09, you wrote:

i appreciate your help. you know that's a lot of work for you to scan all that. don't you want me to just buy a copy of the patch book from you, at least to compensate you for your time?

Jonathan G. Chance, Esq.
JC Law Offices
1840 Gateway Dr.
Suite 200
San Mateo, CA 94404
650-378-1383 (office)
650-921-4696 (cell)
650-429-2048 (fax)
lawjcrg@yahoo. com
www.jchancelaw. com


--- On Sat, 5/30/09, Paul J. White wrote:

From: Paul J. White
Subject: Re: [oberheim] obxa factory presets--do I have dead memory patches?
To: oberheim@yahoogroup s.com
Date: Saturday, May 30, 2009, 5:57 PM

At 04:39 PM 5/30/09, you wrote:
>Hello: at the cost of a small fortune, I've just successfully
>restored an OBX-A that was left for scrap. My repair (surprisingly)
>had a backup tape of the presets from another obxa that had come
>through his shop. Listening to the presents that loaded in and
>comparing them to the preset chart in the owner's manual shows that
>most of these are the factory presets (there may be a couple of the
>other owern's patches thrown in). Here's my issue. for patch A3 and
>the last two groups (CD and ACD) if I push the patch combinations,
>different lights light up, indicating to me that the patch is
>actually loaded and the synth has turned on the various parameters
>that make up that particular patch, e.g, saw versus other waves,
>unison or not, s/h or not, etc.--but NO SOUND comes out. What does
>this indicate? There is something wrong with the memory patch of the
>synth for those patches? Something else? Thanks in advance for any
>suggestions.

I can think of a couple of possibilities:
1. Bad patch tape. Try programming patch A3 manually (see patch
sheet here http://www.electron gate.com/ obfiles/OB- Xa_patch_ A3.jpg)
and see if it works OK.
2. Bad or missing RAM chip. Try storing a working patch in the CD
and ACD banks and see if they stick.

Good luck.

-- Paul White