200e

last night i tried for the first time the MIKE/ MIC in to do some env following...all i got was a really quiet signal, I thought that was strange because i did the same thing with my serge and it was really loud....so then i decided to put the output of the 261 into the mic in , and still it was really quiet i pressed the attenuation buttons but no change.....I am not sure if this is normal?
I am talking the mic in on the 227e

Anyone

Anyone

Bueler

hm.... you used the xlr jack on the rear panel? you tried different settings
of the pre-amp gain (the button)? anything coming out the audio output?

261e out -> xlr input should probably come out kinda loud and distorted...
its a lot of gain...

On Mon, May 4, 2009 at 7:52 PM, cray5656 <amni56@tpg.com.au> wrote:

>
>
> last night i tried for the first time the MIKE/ MIC in to do some env
> following...all i got was a really quiet signal, I thought that was strange
> because i did the same thing with my serge and it was really loud....so then
> i decided to put the output of the 261 into the mic in , and still it was
> really quiet i pressed the attenuation buttons but no change.....I am not
> sure if this is normal?
> I am talking the mic in on the 227e
>
> Anyone
>
> Anyone
>
> Bueler
>
>  
>


[Non-text portions of this message have been removed]

HI Ezra

Should have the 250e back next week :-) missed it

I am inputting the mic into the 227e mike in  then the out env follower 
into a volt/oct...if i try and use the audio out of the mike/env into 
say channel 4 its really quiet...I havent tried the xlr on the back

Ross

ezra buchla wrote:

>
>
> hm.... you used the xlr jack on the rear panel? you tried different 
> settings
> of the pre-amp gain (the button)? anything coming out the audio output?
>
> 261e out -> xlr input should probably come out kinda loud and distorted...
> its a lot of gain...
>
> On Mon, May 4, 2009 at 7:52 PM, cray5656 <amni56@tpg.com.au 
> <mailto:amni56%40tpg.com.au>> wrote:
>
> >
> >
> > last night i tried for the first time the MIKE/ MIC in to do some env
> > following...all i got was a really quiet signal, I thought that was 
> strange
> > because i did the same thing with my serge and it was really 
> loud....so then
> > i decided to put the output of the 261 into the mic in , and still 
> it was
> > really quiet i pressed the attenuation buttons but no change.....I 
> am not
> > sure if this is normal?
> > I am talking the mic in on the 227e
> >
> > Anyone
> >
> > Anyone
> >
> > Bueler
> >
> >
> >
>
> [Non-text portions of this message have been removed]
>
>

i'm not sure what you mean by the "227e mike in" if not the rear XLR jack.
that is the only input. the two 1/8" jacks on the panel are parallel
OUTPUTS.

On Mon, May 4, 2009 at 8:04 PM, amnesia <amni56@tpg.com.au> wrote:

>
>
> HI Ezra
>
> Should have the 250e back next week :-) missed it
>
> I am inputting the mic into the 227e mike in then the out env follower
> into a volt/oct...if i try and use the audio out of the mike/env into
> say channel 4 its really quiet...I havent tried the xlr on the back
>
> Ross
>
>
> ezra buchla wrote:
> >
> >
> > hm.... you used the xlr jack on the rear panel? you tried different
> > settings
> > of the pre-amp gain (the button)? anything coming out the audio output?
> >
> > 261e out -> xlr input should probably come out kinda loud and
> distorted...
> > its a lot of gain...
> >
> > On Mon, May 4, 2009 at 7:52 PM, cray5656 <amni56@tpg.com.au<amni56%40tpg.com.au>
> > <mailto:amni56%40tpg.com.au <amni56%2540tpg.com.au>>> wrote:
> >
> > >
> > >
> > > last night i tried for the first time the MIKE/ MIC in to do some env
> > > following...all i got was a really quiet signal, I thought that was
> > strange
> > > because i did the same thing with my serge and it was really
> > loud....so then
> > > i decided to put the output of the 261 into the mic in , and still
> > it was
> > > really quiet i pressed the attenuation buttons but no change.....I
> > am not
> > > sure if this is normal?
> > > I am talking the mic in on the 227e
> > >
> > > Anyone
> > >
> > > Anyone
> > >
> > > Bueler
> > >
> > >
> > >
> >
> > [Non-text portions of this message have been removed]
> >
> >
>  
>


[Non-text portions of this message have been removed]

oops

On Mon, May 4, 2009 at 8:12 PM, ezra buchla <ezra.buchla@gmail.com> wrote:

> i'm not sure what you mean by the "227e mike in" if not the rear XLR jack.
> that is the only input. the two 1/8" jacks on the panel are parallel
> OUTPUTS.
>
>
> On Mon, May 4, 2009 at 8:04 PM, amnesia <amni56@tpg.com.au> wrote:
>
>>
>>
>> HI Ezra
>>
>> Should have the 250e back next week :-) missed it
>>
>> I am inputting the mic into the 227e mike in then the out env follower
>> into a volt/oct...if i try and use the audio out of the mike/env into
>> say channel 4 its really quiet...I havent tried the xlr on the back
>>
>> Ross
>>
>>
>> ezra buchla wrote:
>> >
>> >
>> > hm.... you used the xlr jack on the rear panel? you tried different
>> > settings
>> > of the pre-amp gain (the button)? anything coming out the audio output?
>> >
>> > 261e out -> xlr input should probably come out kinda loud and
>> distorted...
>> > its a lot of gain...
>> >
>> > On Mon, May 4, 2009 at 7:52 PM, cray5656 <amni56@tpg.com.au<amni56%40tpg.com.au>
>> > <mailto:amni56%40tpg.com.au <amni56%2540tpg.com.au>>> wrote:
>> >
>> > >
>> > >
>> > > last night i tried for the first time the MIKE/ MIC in to do some env
>> > > following...all i got was a really quiet signal, I thought that was
>> > strange
>> > > because i did the same thing with my serge and it was really
>> > loud....so then
>> > > i decided to put the output of the 261 into the mic in , and still
>> > it was
>> > > really quiet i pressed the attenuation buttons but no change.....I
>> > am not
>> > > sure if this is normal?
>> > > I am talking the mic in on the 227e
>> > >
>> > > Anyone
>> > >
>> > > Anyone
>> > >
>> > > Bueler
>> > >
>> > >
>> > >
>> >
>> > [Non-text portions of this message have been removed]
>> >
>> >
>>  
>>
>
>


[Non-text portions of this message have been removed]

ahhh. ok i read the 1/8inch to be signal in and output...will try it 
again tonight

thanks

Ross


ezra buchla wrote:

>
>
> i'm not sure what you mean by the "227e mike in" if not the rear XLR jack.
> that is the only input. the two 1/8" jacks on the panel are parallel
> OUTPUTS.
>
> On Mon, May 4, 2009 at 8:04 PM, amnesia <amni56@tpg.com.au 
> <mailto:amni56%40tpg.com.au>> wrote:
>
> >
> >
> > HI Ezra
> >
> > Should have the 250e back next week :-) missed it
> >
> > I am inputting the mic into the 227e mike in then the out env follower
> > into a volt/oct...if i try and use the audio out of the mike/env into
> > say channel 4 its really quiet...I havent tried the xlr on the back
> >
> > Ross
> >
> >
> > ezra buchla wrote:
> > >
> > >
> > > hm.... you used the xlr jack on the rear panel? you tried different
> > > settings
> > > of the pre-amp gain (the button)? anything coming out the audio 
> output?
> > >
> > > 261e out -> xlr input should probably come out kinda loud and
> > distorted...
> > > its a lot of gain...
> > >
> > > On Mon, May 4, 2009 at 7:52 PM, cray5656 <amni56@tpg.com.au 
> <mailto:amni56%40tpg.com.au><amni56%40tpg.com.au>
> > > <mailto:amni56%40tpg.com.au <amni56%2540tpg.com.au>>> wrote:
> > >
> > > >
> > > >
> > > > last night i tried for the first time the MIKE/ MIC in to do 
> some env
> > > > following...all i got was a really quiet signal, I thought that was
> > > strange
> > > > because i did the same thing with my serge and it was really
> > > loud....so then
> > > > i decided to put the output of the 261 into the mic in , and still
> > > it was
> > > > really quiet i pressed the attenuation buttons but no change.....I
> > > am not
> > > > sure if this is normal?
> > > > I am talking the mic in on the 227e
> > > >
> > > > Anyone
> > > >
> > > > Anyone
> > > >
> > > > Bueler
> > > >
> > > >
> > > >
> > >
> > > [Non-text portions of this message have been removed]
> > >
> > >
> >
> >
>
> [Non-text portions of this message have been removed]
>
>